User manual BIONAIRE BFH3520

[. . . ] · Do not mix alkaline, standard (carbon-zinc), or rechargeable (nickel-cadmium) batteries. The remote control for this unit has the capability of operating all control panel functions (see Fig. MODES: To scroll through the various modes FA, HI, LO, AH, AL and AF press the Mode ( ) Button until you reach your desired setting. OSCILLATION: To start oscillation, press the Oscillation ( ) Button once. [. . . ] Keep the mains cord at a safe distance from the main body of the heater. If overheating should occur, the built-in overheating safety device will switch off the heater. The heater is to be installed so that switches and other controls cannot be touched by a person in the bath. Avoid the use of an extension cord because it may cause the heater to overheat. and Ireland only: If the plug is not suitable for the socket outlets in your home, it can be removed and replaced by a plug of the correct type. and Ireland The wires in the mains lead are coloured as such: BROWN LIVE BLUE NEUTRAL Please note that the colour of these mains wires may not correspond with the colour markings that identify the terminals in your plug. Please proceed as follows: The BROWN coloured wire must be connected to the terminal, which is marked with the letter "L" or is coloured RED. The BLUE coloured wire must be connected to the terminal, which is marked with the letter "N" or is coloured BLACK. DO NOT CONNECT either of these wires to the earth terminal in the plug. The earth terminal plug is marked with the letter "E", or with the earth symbol or coloured GREEN and YELLOW. NOTE: If the terminals in the plug are not marked or if you are unsure or in doubt about the installation of the plug please contact a qualified electrician. If a 13A 3-pin plug is 13 amp fitted, it must be an ASTA approved plug, conforming to BS1363 standard. GUARANTEE PLEASE KEEP YOUR RECEIPT AS THIS WILL BE REQUIRED FOR ANY CLAIMS UNDER THIS GUARANTEE. · In the unlikely event of breakdown, please take it back to the place of purchase, with your till receipt and a copy of this guarantee. · The rights and benefits under this guarantee are additional to your statutory rights which are not affected by this guarantee. · The manufacturer undertakes within the specific period, to repair or replace free of charge, any part of the appliance found to be defective provided that: · We are promptly informed of the defect. · The appliance has not been altered in any way or subjected to misuse or repair by a person other than a person authorised by the manufacturer. · No rights are given under this guarantee to a person acquiring the appliance second hand or for commercial or communal uses. · Any repaired or replaced appliance will be guaranteed on these terms for the remaining portion of the guarantee. Waste electrical products should not be disposed of with Household waste. Check on the following website for further recycling and WEEE information: www. bionaire. com/europe or e-mail info-europe@theholmesgroup. com ® 2. 4KW digital TOWER heater BFH3520 Holmes Products (Europe) Ltd 1 Francis Grove London SW19 4DT England Fax: +44 (0)20 8947 8272 Email: info-europe@theholmesgroup. com Website address: www. bionaire. com/europe UK - Free phone Customer Service Helpline ­ 0800 052 3615 ©2006 JCS/THG, LLC Bionaire®, the Bionaire logoTM and AccuTemp PlusTM are trademarks of JCS/THG, LLC. 9100020007277 BFH3520IUK06EM2 INSTRUCTION MANUAL BFH3520IUK06EM2 V new. qxd 6/16/06 15:13 Page 5 BFH3520 Fig. 1 AND 2) If you are planning on using the pedestal, start with Step 1 Step 1 ­ Turn the heater housing (A) upside down and place on a firm, level surface Step 2 ­ Unscrew the locking nut (E) by turning counterclockwise. Step 3 ­ Unclip the two halves of the pedestal pole (C) and re-clip the two halves (C) around the power cord (F), insert the 2 fixing screws. [. . . ] To prevent the unit from cycling, you need to raise the thermostat setting. When the preset temperature is reached, the fan will run for 30 seconds without heat. This cool down process ensures an accurate and consistent temperature reading. Press the Mode Button one more time to turn the heater to (AF) mode and one final time to turn the heater off. [. . . ]