User manual BIONAIRE BEF6500

[. . . ] DO NOT use this heater with a programmer, timer, separate remote-control system or any other device that switches the heater on automatically, since a fire risk exists if the heater is covered or positioned incorrectly. DO NOT position where it can be touched by children, especially the very young. Allow a safe area around the heater away from furniture or other objects; at least 50 cm from the top and sides and 200 cm at the front. Keep the mains cord at a safe distance from the main body of the heater. [. . . ] Screw in two 4 x 35mm screws into the wall plugs, leaving 10mm of the screws out of the wall. Hang the main body of the unit onto the two exposed screws by lining up the rear mounting brackets' holes. Place the securing bottom bracket (P) into the rear of the unit and then use one 4x35mm screw to secure the bracket and unit to the main wall. Add pebbles to the unit, then place the glass panel onto the unit by lining up the glass panel guides with the main housing pins (located on the side of the housing) and make sure the unit is secure. 3 OPERATING INSTRUCTIONS · There may be an odor coming from the heater the first time you use it. Make sure the heater is in a well ventilated area and continue running it until the smell goes away. · You may hear a popping or crackling sound as the heater heats up. · The Fireplace Heater can be operated by using the remote control (Fig. · Avoid overloading your circuit by not using other high wattage appliances in the same outlet. Turn the main ON/OFF switch (N) on the main unit to the ON (­) position. Either press the mode control (K) or the flame intensity button (M) on the main unit or remote control to start the operation of the unit. If for any reason you would like to turn the unit off press the mode button or flame intensity button on the control panel or the ON/OFF Button (Q) on the remote so that no function is heard or visible and then switch the ON/OFF switch on the main unit to the OFF ( ) postion. MODE SETTINGS Once the main ON/OFF switch has been switched to ON, press the mode control button (K) on the panel or remote control: for Fan only setting 1= for continuous low heat (1kW) 2= for continuous high heat (2kW) Press again for no mode operation. THERMOSTAT Note: Thermostat will operate only if the unit is on the Low (1) or High (2) heat setting. Press the digital thermostat button (J) on the control panel or remote enough times to activate one of the 5 preset desired temperature levels (18°C, 21°C, 24°C, 27°C and 30°C). An LED on the unit or the remote control will illuminate to show the selected setting. The thermostat will now maintain the selected temperature level by automatically turning the heater ON and OFF. If the heater cycles ON/OFF frequently select a higher preset temperature. 4. To switch the digital thermostat mode off, press the digital thermostat button until the LEDs on digital thermostat setting on the control panel or remote are no longer lit. TIMER Note: Timer will work only if one of the three mode settings is used. Press the digital timer button (L) on the control panel or remote enough times to activate one of the 6 preset desired OFF times (2, 4, 6, 8, 10 or 12Hrs) 2. The timer will now turn the unit completely off based on the selected OFF time. [. . . ] and Ireland NOTE: If the terminals in the plug are not marked or if you are unsure or in doubt about the installation of the plug please contact a qualified electrician. If a 13A 3-pin plug is fitted, it must be an ASTA approved plug, conforming to BS1363 standard. If this plug is unsuitable or needs to be replaced, please note the following: The wires in the mains lead are coloured as such: BROWN LIVE BLUE NEUTRAL Please note that the colour of these mains wires may not correspond with the colour markings that identify the terminals in your plug. Please proceed as follows: The BROWN coloured wire must be connected to the terminal, which is marked with the letter "L" or is coloured RED. [. . . ]