User manual BIONAIRE BASF1016GRC

[. . . ] The earth terminal plug is marked with the letter "E", or with the earth symbol , or coloured GREEN, or GREEN and YELLOW. NOTE: If the terminals in the plug are not marked or if you are unsure or in doubt about the installation of the plug please contact a qualified electrician. If a 13A 3-pin plug is fitted, it must be an ASTA approved plug, conforming to BS1363 standard. If this plug is unsuitable or needs to be replaced, please note the following: The wires in the mains lead are coloured as such: BROWN LIVE BLUE NEUTRAL The rights under this guarantee shall only apply to the original purchaser and shall not extend to commercial or communal use. If your appliance includes a country-specific guarantee or warranty insert please refer to the terms and conditions of such guarantee or warranty in place of this guarantee or contact your local authorized dealer for more information. [. . . ] · Do not operate any appliance with a damaged cord, plug, after the appliance malfunctions, or has been dropped/damaged in any manner. · The use of attachments not recommended or sold by the appliance manufacturer may cause hazards. · Do not let the cord hang over the edge of a table or counter, or come into contact with hot surfaces. · To disconnect from the electrical supply, grip the plug and pull from the wall outlet. · This product is intended for household use ONLY and not for commercial or industrial applications. · Should the fan stop working, first check the fuse in the plug (UK only) or fuse/circuit breaker at the distribution board is operating, before contacting the manufacturer or service agent. · If the supply cord or plug is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid hazard. 1 · A B C D E F G J K L H MISSING A PART FOR YOUR FAN?Please call 0800 052 3615 for assistance. DESCRIPTIONS See Figure 1 A. Base This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance. 5. Center the front grill, aligning the Bionaire® logo so it is horizontal and parallel to the floor. The placement is done by a secure press fit that tightens the assembly in place so the fan head should be slightly pressed down. Lower the remote control holder on the right side of the front control housing and place the hollow end of the remote control housing (female end) onto the remote control holder. (Figure 4) REMOTE CONTROL HANDHELD UNIT · The remote includes control buttons for Power on/off " ", and Speed Selections "1 2 3", and Breeze/Sleep Modes " ". · The speed recall memories will also work with the remote control. · Your remote control requires 2 AAA batteries (not included) for operation. · Install the 2 AAA batteries in the rear compartment of the remote, according to the diagram shown inside. · Do not mix alkaline, standard (carbon-zinc), or rechargeable (nickel-cadmium) batteries. ADJUSTMENT Height Adjustment This fan is equipped with an expandable pole, which allows you to adjust the height of the fan according to your preference. BASE POLE ASSEMBLY 1. Extend the upper pole through the top of the lower pole and secure it firmly by turning the height adjust knob clockwise. Insert the bottom of the lower pole into the hole on the top of the base. Figure 2 Figure 3 Figure 4 FAN HEAD ASSEMBLY You are now ready to assemble the fan head. [. . . ] Pressing with no light is for off. CLEANING AND MAINTENANCE Follow these instructions to correctly and safely care for your Bionaire® fan. Please remember: · Always unplug the fan before cleaning or assembly. · Be sure to use a soft cloth, moistened with a mild soap solution. · Do not use any of the following as a cleaner: petrol, thinners or benzene. Tilt Adjustment To change the tilting angle of the fan head, move the fan head manually to the desired angle. Fan Blade cleaning (See instructions for fan head assembly) (See instructions for fan head assembly) 1. [. . . ]