User manual AXIS 27335R1

[. . . ] AXIS 282/282A Bare Board Video Server Installation Guide AXIS 282/282A Installation Guide Page 1 AXIS 282/282A Bare Board Video Server Installation Guide This installation guide is applicable for the following Axis Video Servers: ·AXIS 282: 1-port bare board video server ·AXIS 282A: 1-port bare board video server including 2-way audio For a complete description, get the AXIS 282/282A Bare Board Video Server User's Manual online from Axis Web site, www. axis. com The AXIS 282/282A is a small form factor video server board designed to be built into domes, fixed view cameras, PTZs, analog devices, etc. , and is fully featured for security surveillance and remote monitoring needs. [. . . ] An active speaker with a built-in amplifier can be connected to Line Out (mono) to enable two-way communication. Audio communication can be bi-directional (full-duplex), push to talk (halfduplex) or in one direction only (simplex). Page 2 AXIS 282/282A Installation Guide AXIS 282/282A Top Mounting holes Network connector Terminal I/O connector 34-pin header Mounting hole Mounting hole Not included: ·4 M2 screws - needed for mounting AXIS 282/282A ·34 pin IDC female connector (2mm) AXIS 282/282A Installation Guide Page 3 The Terminal I/O Connector The AXIS 282/282A provides one 4-pin terminal I/O connector. Pin 1 2 3 4 Function Power in/out (8 - 20V) GND Alarm In Alarm Out 1 2 3 4 Note: Pins 3 and 4 in the Terminal I/O Connector are the same Alarm In and Alarm Out as pins 8 and 9 in the 34-Pin Header. If the AXIS 282/282A has been configured to have power going in through the 34 I/O pins, power can be configured to go out through pin 1 of the Terminal I/O Connector. Schematic Diagram - Terminal I/O Connector Network connector The AXIS 282/282A connects to the network via a standard STP network cable, and automatically detects the speed of the local network segment (Ethernet 10BaseT/100BaseTX, RJ-45). Page 4 AXIS 282/282A Installation Guide The 34-Pin Header The AXIS 282/282A has a 34-Pin Header to be used with a 2mm IDC connector. Connections include: ·Serial port, configurable as RS-232 or RS-485, which is typically used for connecting Pan/Tilt/Zoom devices. ·Video in and out connections ·Audio in and out connections ·LED outputs ·DC power auxiliary connection point Pin 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 Function Network LED green Status LED green Flash LED Control button Alarm Out Y/C Video in (Y) Y/C Video in (C) Composite Video In ·AXIS 282: Not used ·AXIS 282A MIC/Line in ·AXIS 282: Not used ·AXIS 282A Audio/Line out RS-485 B Serial port RTS (RS-232) Serial port TXD (RS-232) Serial port GND Power GND Power GND Power IN Pin 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 Function Network LED red Status LED red Power LED Alarm In Ground Y/C GND Y/C GND Composite Video Source GND Mic/Line in GND Line Out GND RS-485 A Serial port CTS (RS-232) Serial port RXD (RS-232) Power GND Power I/O Power IN Power IN AXIS 282/282A Installation Guide Page 5 Schematic Diagram - 34 I/O Pins Note: Pins 8 and 9 in the 34-Pin Connector are the same Alarm In and Alarm Out as pins 3 and 4 in the Terminal I/O Connector. Page 6 AXIS 282/282A Installation Guide AXIS 282/282A Bottom Power LED Network LED Status LED Control button Flash button LED indicators - See AXIS 282/282A User's Manual for a complete listing of the status of the colored Status, Network, and Power indicators. Control button - Used to restore the factory default settings, as described in AXIS 282/282A User's Manual. Used only for firmware programming in the factory and not when upgrading the firmware!See AXIS 282/282A User's Manual for more information. AXIS 282/282A Installation Guide Page 7 Integration of the AXIS 282/282A Mechanical integration may be done through the 4 mounting holes on the AXIS 282/282A, shown in the figure below. Electrical integration of the AXIS 282/282A is done through the connectors described here. Mounting holes Mounting holes 19mm Network Connector Control button Flash button Page 8 AXIS 282/282A Installation Guide Technical Specifications Item Models Specification · AXIS AXIS 282: 1-channel bare board video server · AXIS AXIS 282A: 1-channel bare board video server with two-way audio Audio features · G. 711 PCM 64kbit/s, G. 726 ADPCM 32 or 24 kbit/s, full duplex, half AXIS 282A only duplex, simplex or audio off Connectors · One 34-pin I/O header - 1 analog composite or Y/C video input (NTSC/PAL autosensing ) - RS-485 or RS-232 port - 1 alarm input, 1 alarm output - Power connection (input and output) - LED outputs - Audio input (282A): Microphone (54 mVpp) or Line in (8. 0 Vpp), mono - Audio output (282A): Line out (2. 6 Vpp), mono · Terminal block: - 1 alarm input, 1 alarm output - Alternative power connection · Ethernet 10Base/100BaseTX, RJ-45 connector · Via pin 3 of the Terminal Block: 8 - 20V DC, max 8W · Via pins 32 - 34 of the 34-pin header: 8 -20V DC, max 8W · Temperature: 5oC (41oF) to 50oC (122oF) · Humidity: 20-80% RH (non-condensing) User's manual and installation tool available at www. axis. com Web-based configuration, Configuration backup and restore Firmware upgrades over HTTP or FTP, firmware available at www. axis. com · AXIS 282/AXIS 282A is delivered as a component for the sole purpose of being integrated into a product or system. [. . . ] · HxWxD = 19 x 79 x 82mm (3/4" x 3 1/8" x 3 1/4") · Weight: 60g (2 1/8oz) Power Operating conditions Installation, management and maintenance Approvals Dimensions For a complete detailed description of technical specifications see the AXIS 282/282A Bare Board Video Server User's Manual. AXIS 282/282A Installation Guide v1. 0 Copyright © Axis Communications AB, 2006 August 2006 Part No. [. . . ]