User manual ATLINKS VERSATIS M250

[. . . ] the base l Connect up the telephone and power cables. The base lamp lights up to show that the base is connected to the mains. . . . the handset l Connect and install the batteries, and fit the battery cover. ! Only use rechargeable batteries with the same specifications as those supplied with the product. Using non-rechargeable or nonconforming batteries could damage the product (see "Technical Specifications"). Failure to comply with this recommendation will invalidate the manufacturer's warranty. Versatis-150_uk. qxd 08/03/02 15:46 Page 7 7 l Place the handset on its base. 4 The indicator light flashes: the batteries are on charge. Before using for the first time, we recommend that you leave the handset to charge up on the base for 24 hours in order to optimize battery performance and longevity. l Seize the line . 4 The dial tone confirms that your VERSATIS is working. [. . . ] . Dial the number of the desired entry (0 to 9) Note: The VERSATIS displays 12 digits on the same display line. 20 digits), it will be displayed in two parts: l The beginning of the number is displayed first: Press to view the second part. l Versatis-150_uk. qxd 08/03/02 15:47 Page 16 16 3. 4 l l l l l MODIFYING OR DELETING A CONTACT PAGE Press Press Press Press Press . or to find the desired entry, or dial the corresponding number . for 2 seconds. for 2 seconds to confirm. 3. 5 l l l DELETING ALL THE CONTACT PAGES Press Press Press . for 2 seconds. Versatis-150_uk. qxd 08/03/02 15:47 Page 17 17 4. IDENTIFYING YOUR CALLERS If you subscribe to your network operator's "Caller Line Identification" (CLI) service, you can see your correspondent's number before you take the call. The last 20 calls received (whether answered or unanswered) are logged along with the corresponding number, date and time. If the same correspondent has called more than once, only the most recent call is stored in the log. flashes to indicate that a new call has been received and has not yet been consulted 4. 1 l CONSULTING THE INCOMING CALLS LOG Press . 4 The most recent call is shown first. l Press or for the previous or following number. To quit the log, after or during consultation, l Press for 2 seconds. The number (first 12 digits only) appears along with the date and time the call was received. , or . 4 The 3 available melodies are played back. l Press to select the desired volume (loud or soft). Once you have made your selection: l Press for 2 seconds to confirm your settings. Versatis-150_uk. qxd 08/03/02 15:48 Page 22 22 6. 2 TURNING OFF THE HANDSET RINGER If you don't want to be disturbed by the handset ringing: l l Press Press for 2 seconds to access the Programming menu. for 2 seconds to confirm. 4 l Press Repeat the procedure to reactivate the ringer: l l Press Press for 2 seconds to access the Programming menu. The number will appear on the left of the display. 4 The internal correspondent answers. l Press for 2 seconds. 4 All three correspondents are on line. l Press to hang up. Versatis-150_uk. qxd 08/03/02 15:50 Page 31 31 8. TECHNICAL SPECIFICATIONS Free field range Indoor range Handset battery life (average values**) Number of handsets Weight of handset Mains adapter 300 meters * 50 meters * 6 hours talktime** 60 hours standby Up to 5 128 grams (with batteries) Input: 230V AC, 50 Hz / 40 mA Output: 9V DC, 350 mA Rechargeable batteries Operating temperature 2. 4 V / 300 mAh / Ni-Cd AAA size x 2 (pack) 5 to 40° C * Value may vary according to environment. ** For guidance only; depends on initial battery charge. Versatis-150_uk. qxd 08/03/02 15:50 Page 32 32 9. TROUBLESHOOTING . . . If a problem arises, try this first: remove the batteries from all the handsets in your installation for about 1 minute; disconnect and then reconnect the power supply to the base; reinstall the batteries. There is no dial tone, or you hear a sequence of error beeps during a call (you may be cut off). You are out of range of the base or in an environment prone to interference. See "Adding a New Handset". Put the handset back on its base to recharge it. Move nearer to the base. Versatis-150_uk. qxd 08/03/02 15:50 Page 33 33 9. Ask your Alcatel reseller to supply you with new batteries. The base or charger is not powered up. The handset batteries are defective. If the problem recurs, call our hotline: the number is given on the cover. The store where you purchased your VERSATIS can also advise you and provide after-sales support. Versatis-150_uk. qxd 08/03/02 15:50 Page 34 34 10. [. . . ] Its input is classified as hazardous and its output as SELV (Security Extra Low Voltage). The mains adapter must be installed close to the device and must be easily accessible. To disconnect the device from the primary power source, the mains adapter must be removed from the 230V AC 50 Hz outlet. If the mains adapter fails, it must be replaced by an identical model. If not connected to the mains power or if there is a mains power failure, installations with cordless handsets will no longer work. [. . . ]