User manual AT&T TL32100

[. . . ] User's manual TL32100/TL32200/TL32300 DECT 6. 0 cordless telephone/ answering system with caller ID/call waiting Congratulations on purchasing your new AT&T product. Before using this AT&T product, please read Important safety information on page 77 of this user's manual. Please thoroughly read the user's manual for all the feature operations and troubleshooting information you need to install and operate your new AT&T product. You can also visit our website at www. telephones. att. com or call 1 (800) 222-3111. [. . . ] In this case, allow six seconds per ring when determining the appropriate setting. Answering system new message indication When there are new messages (including memos) on the answering system, the number of new messages stored flashes in the message window on the telephone base and the icon and XX new messages HANDSET 1 appear on the screen of each system handset. If the new 16 new messages message alert tone is turned on, the telephone base beeps every 10 seconds when there are new messages. 10/20 10:30PM To listen to messages recorded on your digital answering system, use the Play messages menu from a handset or press PLAY/STOP on the telephone base (see To listen to messages on page 53). 50 Answering system Answering system overview Voice prompts The system provides voice prompts to guide you through recording announcements and remote access. Message capacity The answering system can record up to 99 messages, depending on the length of each message. Individual messages can be up to the time you set (see Recording time on page 21; individual memos can be up to three minutes), and the approximate recording time is 14 minutes. The actual recording time depends on individual message characteristics. At the beginning of messages playback, if the answering system has less than three minutes of recording time left, the answering system announces, "Less than three minutes to record. " If the memory is full, the answering system announces, "Memory is full. " If the memory is full, the number of messages and F flash alternately in the message window, and Memory full appears on the handset screen. Call screening Call screening on the telephone base: If the answering system and call screening are on, the announcement and the incoming message can be heard through the telephone base when a call arrives. You can turn call screening on or off using the handset (see Call screening setup on page 19). When call screening is off, you can temporarily turn on the call screening by pressing PLAY/STOP or VOLUME on the telephone base. If call screening is on and you want to adjust the playback volume to a comfortable level (1-8) while it is recording messages, press VOLUME on the telephone base. This volume setting is shared with message playback, so when you play messages at volume 1, they play at a very low volume. If you turn up the volume for playback, the call screening for the next incoming message plays at the same volume level. If call screening is on and you want to silence the telephone base while it is recording messages, press PLAY/STOP on the telephone base. The call screening will be on for the next incoming call. 51 Answering system Answering system overview Call screening on a handset: TO SCREEN CALL, 1. If the answering system is on, the handset shows PRESS [SELECT] TO SCREEN CALL, PRESS [SELECT] when a call arrives. The announcement and the incoming message broadcast from the handset speakerphone. · Press DIR/VOLUME to increase or CID/VOLUME to decrease the message playback volume. · Press SPEAKER to switch between the speakerphone and handset earpiece. · Press EQUALIZER to change the quality of the audio of the handset to best suit your hearing (see Equalizer on page 28). · If using the handset earpiece, press AUDIO ASSIST to enhance the clarity and loudness of your caller's voice (see Audio assistTM on page 28). [. . . ] Except as provided by applicable law, you assume the risk of loss or damage during transit and transportation and are responsible for delivery or handling charges incurred in the transport of the PRODUCT(s) to the service location. The manufacturer will return repaired or replaced PRODUCT under this limited warranty. The manufacturer assumes no risk for damage or loss of the PRODUCT in transit. If the PRODUCT failure is not covered by this limited warranty, or proof of purchase does not meet the terms of this limited warranty, the manufacturer notifies you and requests that you authorize the cost of repair prior to any further repair activity. [. . . ]