User manual AT&T SB67128

[. . . ] Issue 3 AT&T 09/09 www. telephones. att. com User's manual Part 2 1 (866) 288-4268. Before you install Parts list · · · · · B62 DECT 6. 0 repeater Power adapter Part Important product information Part 2 User's manual Package of screws Use only the power adapter supplied with this product. To obtain a replacement, visit our website at www. telephones. att. com or call 1 (888) 915-2007. In Canada, dial 1 (866) 288-4268. Figure : Repeater About the repeater You can use a repeater to extend the operating range for the AT&T B6 DECT 6. 0 4-line corded/cordless telephone system to cover areas where the signal is very weak or not available. The repeater extends the range in all directions, even going around certain barriers. [. . . ] A registered repeater does not count as an extension and does not have an assigned extension number within the telephone system. For complete registration instructions of B6 telephone base, please refer to the manual provided with your AT&T B6 product, or visit www. telephones. att. com to download the manual. SETUP button 3 Registration STATUS indicator light Slow flash The repeater is powered on and in idle mode waiting to be reregistered. The repeater is successfully registered and in a normal operation mode. The repeater has no power. Quick flash On Off 4 Installation After you have plugged in your repeaters in the locations you think are best, place a call from a cordless handset (AT&T B60) and while talking, move around the building to test the reception. You may want to adjust the position of repeaters to receive the best reception. Plug the small end of the power adapter into the power jack on the front of the repeater and route the cord through the slot on the bottom of the repeater. Plug the large end of the power adapter into a standard electrical outlet not controlled by a wall switch. Route the power adapter cord through the slot on the bottom of the repeater. Plug the small end of the power adapter into the power jack on the bottom of the repeater. Raise the antennas. Figure 3: Connect the power adapter to the repeater 5 Installation You can place the repeater on a tabletop. You can install your repeater on a wall or other object with the provided screws. Please use the recommended placement and installation tips as follows: · The antennas needs to be in a high location (not on the floor or under a desk) for reception. · Maintain a minimum of 30 feet distance between each repeater. If you place the repeater on a tabletop, plug the large end of the power adapter into a nearby electrical wall outlet and raise the antennas. Figure 4: Tabletop installation 6 Installation If you want to install your repeater on a wall or other object, use the provided screws. Professional assistance may be required to install screws on the wall. Then plug the large end of the power adapter into a nearby electrical wall outlet and raise the antennas. ^ ^ crew spacing=2. 5 inches Figure 5: Wall installation crew holes NOTE: The power adapter is intended to be correctly oriented in a vertical or floor mount position. The prongs are not designed to hold the plug in place if it is plugged into a ceiling, under-the-table or cabinet outlet. Troubleshooting If you have difficulty operating this repeater, try the suggestions below. To contact Customer ervice, purchase accessories or obtain replacement parts, visit our website at www. telephones. att. com or call 1 (888) 915-2007. If the light is off or flashing, the repeater is not registered or the base has no power. · Make sure you install the repeater in a high location (not on the floor or under a desk) for better reception. · Do not place the repeater near a microwave oven or on the same electrical outlet. [. . . ] Power failure recovery. · You can register a repeater to an B6 telephone base without deregistering it from a previous telephone base. New registrations overwrite any previous repeater registrations. · Your registered repeater automatically links to the telephone base wherever power is restored. The STATUS indicator light is on when there is a valid link. 9 General product care To keep the repeater working and looking good, follow these guidelines: · Avoid putting it near appliances and devices that generate electrical noise (motors, fluorescent lights, etc. ) · DO NOT expose it to direct sunlight or moisture. · Never use a strong cleaning agent or abrasive powder because this will damage the finish. [. . . ]