User manual AT&T DECT 6.0

[. . . ] User's manual EL52200/EL52250/EL52300/ EL52350/EL52400/EL52450/ EL52500/EL52510 DECT 6. 0 cordless telephone/ answering system with caller ID/call waiting Congratulations on purchasing your new AT&T product. Before using this AT&T product, please read Important safety information on page 67 of this user's manual. Please thoroughly read the user's manual for all the feature operations and troubleshooting information you need to install and operate your new AT&T product. You can also visit our website at www. telephones. att. com or call 1 (800) 222-3111. [. . . ] To use your answering system rather than your voicemail service, contact your telephone service provider to deactivate your voicemail service. You can also use your telephone answering system and voicemail together by setting your built-in answering system to answer before voicemail answers as described below. To learn how to program your voicemail settings, contact your telephone service provider. Then, if you are on a call, or if the answering system is busy recording a message and you receive another call, the second caller can leave a voicemail message. If you have voicemail provided by your telephone service provider, we recommend setting your answering system to answer calls at least two rings earlier than your voicemail is set to answer. For example, if your voicemail answers after six rings, set your answering system to answer after four rings. Some voicemail providers may program the delay before answering calls in seconds instead of rings. In this case, allow six seconds per ring when determining the appropriate setting. Answering system new message indication When there are new messages (including memos) on the answering system, the number of new messages stored flashes in the message window on the telephone base and the icon and XX NEW MESSAGES HANDSET 1 appear on the screen of each system handset. If the new 16 NEW MESSAGES message alert tone is turned on, the telephone base beeps every 10 seconds when there are new messages. 10:30PM 11/20 To listen to messages recorded on your digital answering system, use the PLAY MESSAGES menu from a handset or press PLAY/STOP on the telephone base (see Message playback on page 46). 43 Answering system Answering system overview Voice prompts The system provides voice prompts to guide you through recording announcements and remote access. Message capacity The answering system can record up to 99 messages, depending on the length of each message. Individual messages can be up to four minutes, and the approximate recording time is 14 minutes. The actual recording time depends on individual message characteristics. If the answering system has less than three minutes of recording time left, the remaining time is announced at the end of messages playback. If the memory is full, the answering system announces, "Memory is full. " The number of messages and F flash alternately in the message window, and REC MEM FULL appears on the handset screen. Call screening If the answering system and call screening are on, the announcement and the incoming message broadcast at the telephone base when a call arrives. You can turn call screening on or off using the handset (see Call screening setup on page 17). When call screening is off, you can temporarily turn on the call screening by pressing PLAY/STOP or VOLUME on the telephone base. If call screening is on and you want to adjust the playback volume to a comfortable level (1-8) while it is recording messages, press VOLUME on the telephone base. This volume setting is shared with message playback, so when you play messages at volume 1, they play at a very low volume. If you turn up the volume for playback, the call screening for the next incoming message plays at the same volume level. [. . . ] Except as provided by applicable law, you assume the risk of loss or damage during transit and transportation and are responsible for delivery or handling charges incurred in the transport of the PRODUCT(s) to the service location. The manufacturer will return repaired or replaced PRODUCT under this limited warranty. The manufacturer assumes no risk for damage or loss of the PRODUCT in transit. If the PRODUCT failure is not covered by this limited warranty, or proof of purchase does not meet the terms of this limited warranty, the manufacturer notifies you and requests that you authorize the cost of repair prior to any further repair activity. [. . . ]