User manual ASUS VH222T

[. . . ] Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners' benefit, without intent to infringe. · Adobe and Acrobat are registered trademarks of Adobe Systems Incorporated. · AMD, K6, Super7, and combinations thereof are trademarks of Advanced Micro Devices, Inc. · Cyrix, M II, and combinations thereof are trademarks of National Semiconductor Corporation. · Intel, LANDesk, and Pentium are registered trademarks of Intel Corporation. [. . . ] This entry provides three options: Normal, Large, LBA, or Auto (see below). Set MODE to the Normal for IDE hard disk drives smaller than 528MB; set it to LBA for drives over 528MB that support Logical Block Addressing (LBA) to allow larger IDE hard disks; set it to Large for drives over 528MB that do not support LBA. Large type of drive can only be used with MS-DOS and is very uncommon. Most IDE drives over 528MB support the LBA mode. ASUS VH222T User's Manual 41 IV. BIOS SETUP Auto detection of hard disks on bootup For each field: Primary Master, Primary Slave, Secondary Master, and Secondary Slave, you can select Auto under the TYPE and MODE fields. This will allow you to change your hard disks (with the power off) and then power on without having to reconfigure your hard disk type. If you use older hard disks that do not support this feature, then you must configure the hard disk in the standard method as described earlier by the "User" option. NOTE: After the IDE hard disk drive information has been entered into BIOS, new IDE hard disk drives must be partitioned (such as with FDISK) and then formatted before data can be read from and write on. Primary IDE hard disk drives must have its partition set to active (also possible with FDISK). NOTE: SETUP Defaults are noted in parenthesis next to each function heading. Drive A / Drive B (None) These fields record the types of floppy disk drives installed in your system. The available options for drives A and B are: 360K , 5. 25 in. ; 1. 2M , 5. 25 in. ; 720K , 3. 5 in. ; 1. 44M , 3. 5 in. ; 2. 88M , 3. 5 in. ; None IV. BIOS SETUP Standard CMOS 42 To enter the configuration value for a particular drive, highlight its corresponding field and then select the drive type using the left- or right-arrow keys. This allows multiple operating systems to be used on both IDE and SCSI drives or the primary operating system to boot using a SCSI hard disk drive. Boot Sequence (A, C) This field determines where the system looks first for an operating system. Options are A, C; A, CDROM, C; CDROM, C, A; CDROM A, C; D, A; E, A; F, A; C only; LS/ZIP, C; LAN, A, C; LAN, C, A; and C, A. The setup default setting, A, C, checks first the floppy disk and then the hard disk drive. Boot Up Floppy Seek (Disabled) When enabled, the BIOS will seek drive A one time. Floppy Disk Access Control (R/W) This allows protection of files from the computer system to be copied to floppy disk drives by allowing the setting of Read Only to only allow reads from the floppy disk drive but not writes. IDE HDD Block Mode Sectors (HDD MAX) This field enhances hard disk performance by making multi-sector transfers instead of one sector per transfer. (Self-Monitoring Analysis and Reporting Technology) support for S. M. A. R. T. -capable hard disk drives. PS/2 Mouse Function Control (Auto) The setting of Auto allows the system to detect a PS/2 Mouse on bootup. OS/2 Onboard Memory > 64M (Disabled) When using OS/2 operating systems with installed DRAM of greater than 64MB, you need to Enable this option otherwise leave this on the setup default of Disabled. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] S/W REFERDMI Utility ENCE 92 Use the (left-right) cursors to move the top menu items and the (up-down) cursor to move between the left hand menu items. The bottom of the screen will show the available keys for each screen. Press enter at the menu item to enter the right hand screen for editing. The reversed color field is the current cursor position and the blue text are available for editing. [. . . ]