User manual ASUS VH222S

[. . . ] IN NO EVENT SHALL ASUS, ITS DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT. SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE, AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners' benefit, without intent to infringe. ii Contents Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Connect one end of the chassis intrusion sensor or switch cable to this connector. The chassis intrusion sensor or switch sends a high-level signal to this connector when a chassis component is removed or replaced. By default, the pins labeled "Chassis Signal" and "Ground" are shorted with a jumper cap. Remove the jumper caps only when you intend to use the chassis intrusion detection feature. CHASSIS ® Chassis intrusion connector ASUS VH222S/P5V-VM SE DH (Default) Chassis Signal GND +5VSB_MB 1-35 13. MP3-In connector (4-pin MP3IN [red]) (Only for P5V-VM SE DH) This connector is for the MP3-In module that allows you to connect your MP3 player to the speakers of the computer. For more information, refer to the MP3-InTM quick installation guide for details. MP3IN ® Right Audio Channel Ground Ground Left Audio Channel MP3 connector · The MP3-In module is bundled with the motherboard package. Connect the cable to the MP3IN connector, and enjoy music from computer speakers even when the PC is turned off. Do not plug the MP3-In cable into the Audio-in connector. · 1-36 Chapter 1: Product introduction 14. System panel connector (20-8 pin F_PANEL) This connector supports several chassis-mounted functions. PLED PLED+ PLED- SPEAKER +5V Ground Ground Speaker PANEL IDE_LED+ IDE_LED® IDE_LED RESET System panel connector * Requires an ATX power supply. PWRSW · System power LED (3-pin PLED) · This 3-pin connector is for the system power LED. The system power LED lights up when you turn on the system power, and blinks when the system is in sleep mode. Hard disk drive activity LED (2-pin IDE_LED) This 2-pin connector is for the HDD Activity LED. A Format 3 1/2 Floppy Disk window appears. Windows® 2000 environment e. Select Create an MS-DOS startup disk from the format options field, then click Start. Insert the Windows® 2000 CD to the optical drive. D:\bootdisk\makeboot a: e. Copy the original or the latest motherboard BIOS file to the bootable floppy disk. assuming that D: is your optical drive. ASUS VH222S/P5V-VM SE DH 2-5 2. 1. 3 ASUS EZ Flash 2 utility The ASUS EZ Flash 2 feature allows you to update the BIOS without having to go through the long process of booting from a floppy disk and using a DOS-based utility. The EZ Flash utility is built-in the BIOS chip so it is accessible by pressing <Alt> + <F2> during the Power-On Self Tests (POST). Visit the ASUS website (www. asus. com) to download the latest BIOS file for the motherboard. Save the BIOS file to a floppy disk/USB flash disk, then restart the system. (1) Insert the floppy disk/USB flash disk that contains the BIOS file to the floppy disk drive or the USB port. Press <Alt> + <F2> during POST to display the following. ASUSTek EZ Flash 2 BIOS ROM Utility V3. 00 FLASH TYPE: Winbond W39V040C/FC (4Mb) Current ROM Update ROM BOARD: VH222S BOARD: Unknown VER: 0105 VER: Unknown DATE: 09/13/06 DATE: Unknown PATH: A:\ A: B: Note [Enter] Select or Load [Tab] Switch [B] Backup [ESC] Exit [Up/Down/Home/End] Move (2) Enter BIOS setup program. Go to the Tools menu to select EZ Flash 2 and press <Enter> to enable it. [. . . ] Press <Y> to confirm; otherwise, press <N>. JMicron Technology Corp. PCI-to-SATA II/IDE RAID Controller BIOS v0. 97 [Create New RAID] Name: JRAID Level: 0-Stripe Disks: Select Disk Block: 128 KB Size : 319 GB Confirm Creation [RAID Disk Drive List] [Hard Disk Drive List] Model Name HDD0: HDS722516VLSA80 HDD1: HDS722516DLA380 Capacity 164 GB 164 GB Type/Status Non-RAID Non-RAID Create RAID on the selected HDD (Y/N)?Y [ TAB]-Switch Window []-Select Item [ENTER]-Action [ESC]-Exit Pressing <Y> deletes all the data in the HDDs. 6. The following screen appears, displaying the relevant information about the RAID set you created. [RAID Disk Drive List] Model Name RAID Level RDD0: JRAID 0-Stripe Capacity XXX GB Status Members(HDDx) Normal 01 ASUS VH222S/P5V-VM SE DH 3-15 Deleting a RAID set 1. In the main JMB363 RAID BIOS menu, highlight Delete RAID Disk Drive using the up/down arrow key then press <Enter>. [Main Menu] Create RAID Disk Drive Delete RAID Disk Drive Revert HDD to Non-RAID Repair Mirror Conflict Save and Exit Setup Exit Without Saving 2. Use the space bar to select the RAID set you want to delete. [. . . ]