User manual ASUS P5Q SE2 QUICK START GUIDE

[. . . ] Motherboard P5Q SE2 E4200 First Edition V1 September 2008 Copyright © 2008 ASUSTeK Computer, Inc. No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK Computer Inc. Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the product is defaced or missing. ASUS PROVIDES THIS MANUAL "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. [. . . ] Do not place jumper caps on the fan connectors! CHA_FAN GND +12V Rotation CPU_FAN P5Q SE2 PWR_FAN Rotation +12V GND P5Q SE2 fan connectors Only the CPU fan supports the ASUS Q-FAN feature. 1-22 GND RSATA_RXN5 RSATA_RXP5 GND RSATA_TXN5 RSATA_TXP5 GND GND CPU FAN PWR CPU FAN IN CPU FAN PWM Chapter 1: Product introduction GND RSATA_RXN3 RSATA_RXP3 GND RSATA_TXN3 RSATA_TXP3 GND GND RSATA_TXN2 RSATA_TXP2 GND RSATA_RXN2 RSATA_RXP2 GND SATA1 6. . USB. connectors. (10-1. pin. USB78, . USB910, . USB1112) These connectors are for USB 2. 0 ports. Connect the USB module cable to any of these connectors, then install the module to a slot opening at the back of the system chassis. These USB connectors comply with USB 2. 0 specification that supports up to 480Mbps connection speed. USB1112 USB+5V USB_P12USB_P12+ GND NC USB78 USB+5V USB_P10USB_P10+ GND NC USB910 USB+5V USB_P8USB_P8+ GND NC PIN 1 P5Q SE2 PIN 1 PIN 1 USB+5V USB_P11USB_P11+ GND USB+5V USB_P9USB_P9+ GND P5Q SE2 USB2. 0 connectors Never connect a 1394 cable to the USB connectors. The USB module cable is purchased separately. 7. . Serial. port. connector. (10-1. pin. COM1) This connector is for a serial (COM) port. Connect the serial port module cable to this connector, then install the module to a slot opening at the back of the system chassis. COM1 PIN 1 P5Q SE2 P5Q SE2 Serial port (COM1) connector The serial port module is purchased separately. ASUS P5Q SE2 USB+5V USB_P7USB_P7+ GND 1-23 8. . Front. panel. audio. connector. (10-1. pin. AAFP) This connector is for a chassis-mounted front panel audio I/O module that supports either HD Audio or legacy AC`97 audio standard. Connect one end of the front panel audio I/O module cable to this connector. GND PRESENCE# SENSE1_RETUR SENSE2_RETUR AGND NC NC PIN 1 AAFP PIN 1 P5Q SE2 HD-audio-compliant pin definition PORT1 L PORT1 R PORT2 R SENSE_SEND PORT1 L Legacy AC'97 compliant definition P5Q SE2 Analog front panel connector · We recommend that you connect a high-definition front panel audio module to this connector to avail of the motherboard's high-definition audio capability. · If you want to connect a high-definition front panel audio module to this connector, set the Front. Panel. Type item in the BIOS setup to [HD. Audio];. if you want to connect an AC'97 front panel audio module to this connector, set the item to [AC97]. By default, this connector is set to [HD. Audio]. . See section 2. 5. 3 Onboard Devices Configuration for details. 9. . Chassis. intrusion. connector. (4-1. pin. CHASSIS) This connector is for a chassis-mounted intrusion detection sensor or switch. Connect one end of the chassis intrusion sensor or switch cable to this connector. The chassis intrusion sensor or switch sends a high-level signal to this connector when a chassis component is removed or replaced. By default, the pin labeled "Chassis Signal" and "Ground" are shorted with a jumper cap. Remove the jumper caps only when you intend to use the chassis intrusion detection feature. P5Q SE2 Chassis Signal GND +5VSB_MB CHASSIS P5Q SE2 Chassis intrusion connector 1-24 MIC2 MICPWR Line out_R NC Line out_L Chapter 1: Product introduction NC 10. . Optical. drive. audio. connector. (4-pin. CD) These connectors allow you to receive stereo audio input from sound sources such as a CD-ROM, TV tuner, or MPEG card. CD Left Audio Channel GND GND Right Audio Channel P5Q SE2 P5Q SE2 Internal audio connector 11. . ATX. power. connectors. (24-pin. EATXPWR, . 4-pin. EATX12V) These connectors are for ATX power supply plugs. The power supply plugs are designed to fit these connectors in only one orientation. Find the proper orientation and push down firmly until the connectors completely fit. ATX12V +12V DC +12V DC EATXPWR PIN 1 P5Q SE2 PIN 1 +3 Volts -12 Volts GND PSPN# GND GND GND -5 Volts +5 Volts +5 Volts +5 Volts GND +3 Volts +3 Volts GND +5 Volts GND +5 Volts GND Power OK +5V Staudby +12 Volts +12 Volts +3 Volts P5Q SE2 ATX power connectors · For a fully configured system, we recommend that you use a power supply unit (PSU) that complies with ATX 12 V Specification 2. 0 (or later version) and provides a minimum power of 400 W. · Do not forget to connect the 4-pin EATX12V power plug; otherwise, the system will not boot. · Use of a PSU with a higher power output is recommended when configuring a system with more power-consuming devices. The system may become unstable or may not boot up if the power is inadequate. · The ATX 12 V Specification 2. 0-compliant (400W) PSU has been tested to support the motherboard power requirements with the following configuration: CPU: Intel® Pentium® Extreme 3. 73GHz Memory: 512 MB DDR2 (x4) Graphics card: ASUS EAX1900XT Parallel ATA device: IDE hard disk drive Serial ATA device: SATA hard disk drive (x2) Optical drive: DVD-RW ASUS P5Q SE2 GND GND 1-25 12. . System. panel. connector. (20-8. pin. PANEL) This connector supports several chassis-mounted functions. PLED SPEAKER PANEL PIN 1 PWR Ground PWRSW P5Q SE2 IDE_LED IDE_LED+ IDE_LED- RESET * Requires an ATX power supply P5Q SE2 System panel connector ·. System. power. LED. (2-pin. PLED) This 2-pin connector is for the system power LED. [. . . ] Select an item then press <Enter> to display the sub-menu. Main Ai Tweaker BIOS SETUP UTILITY Advanced Power Boot Tools Exit ASUS EZ Flash 2 Express Gate Enter OS Timer Reset User Data AI NET 2 ASUS O. C. Profile [Enabled] [10 Seconds] [No] Press ENTER to run the utility to select and update BIOS. This utility doesn't support: 1. NTFS format 2. 8. 1. Allows you to run ASUS EZ Flash 2. Use the left/right arrow key to select between [Yes] or [No], then press <Enter> to confirm your choice. [. . . ]