User manual ASUS P5N32-SLI PREMIUM

[. . . ] P5N32-SLI Premium Motherboard E2749 First Edition V1 August 2006 Copyright © 2006 ASUSTeK COMPUTER INC. No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the product is defaced or missing. ASUS PROVIDES THIS MANUAL "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. [. . . ] See section "4. 4. 7 Onboard Device Configuration" for details. SATA1 P5N32-SLI PREMIUM SATA3 GND RSATA_RXN3 RSATA_RXP3 GND RSATA_TXN3 RSATA_TXP3 GND SATA5 GND RSATA_RXN5 RSATA_RXP5 GND RSATA_TXN5 RSATA_TXP5 GND ® SATA2 GND RSATA_RXN2 RSATA_RXP2 GND RSATA_TXN2 RSATA_TXP2 GND P5N32-SLI PREMIUM SATA connectors These connectors support Native Command Queuing (NCQ), Power Management (PM) Implementation Algorithm, Hot Swap and smart setup. GND RSATA_RXN1 RSATA_RXP1 GND RSATA_TXN1 RSATA_TXP1 GND SATA4 GND RSATA_RXN4 RSATA_RXP4 GND RSATA_TXN4 RSATA_TXP4 GND SATA6 GND RSATA_RXN6 RSATA_RXP6 GND RSATA_TXN6 RSATA_TXP6 GND 2-26 Chapter 2: Hardware information Right-angle side Connect the right-angle side of SATA signal cable to the SATA device, or connect the right-angle side of the SATA cable to the onboard SATA port to avoid mechanical conflict with huge graphics cards. 4. USB connectors (10-1 pin USB56, USB78) These connectors are for USB 2. 0 ports. Connect the USB module cable to any of these connectors, then install the module to a slot opening at the back of the system chassis. These USB connectors comply with USB 2. 0 specification that supports up to 480 Mbps connection speed. P5N32-SLI PREMIUM NC GND USB_P8+ USB_P8USB+5V NC GND USB_P6+ USB_P6USB+5V ® USB56 1 USB78 GND USB_P5+ USB_P5USB+5V 1 GND USB_P7+ USB_P7USB+5V P5N32-SLI PREMIUM USB 2. 0 connectors Never connect a 1394 cable to the USB connectors. You can connect the USB cable to ASUS Q-Connector (USB, blue) first, and then install the Q-Connector (USB) to the USB connector onboard. ASUS P5N32-SLI Premium 2-27 5. IEEE 1394a port connector (10-1 pin IE1394_2) This connector is for a IEEE 1394a port. Connect the IEEE 1394a module cable to this connector, then install the module to a slot opening at the back of the system chassis. P5N32-SLI PREMIUM GND +12V TPB2GND TPA2- ® IE1394_2 P5N32-SLI PREMIUM IEEE 1394 connector 1 Never connect a USB cable to the IEEE 1394a connector. You can connect the 1394 cable to ASUS Q-Connector (1394, red) first, and then install the Q-Connector (1394) to the 1394 connector onboard. +12V TPB2+ GND TPA2+ 2-28 Chapter 2: Hardware information 6. CPU, chassis, and power fan connectors (4-pin CPU_FAN, 3-pin CHA_FAN1, 3-pin CHA_FAN2, 3-pin CHA_FAN3, 3-pin PWR_FAN) The fan connectors support cooling fans of 350 mA ~ 2000 mA (24 W max. ) or a total of 1 A ~ 7 A (84 W max. ) at +12V. Connect the fan cables to the fan connectors on the motherboard, making sure that the black wire of each cable matches the ground pin of the connector. Do not forget to connect the fan cables to the fan connectors. Insufficient air flow inside the system may damage the motherboard components. Do not place jumper caps on the fan connectors! CPU_FAN PWR_FAN P5N32-SLI PREMIUM CPU_FAN CPU FAN PWM CPU FAN IN CPU FAN PWR GND PWR_FAN GND +12V Rotation CHA_FAN1 ® CHA_FAN1 CHA_FAN2 CHA_FAN3 GND +12V Rotation GND +12V Rotation CHA_FAN2 CHA_FAN3 P5N32-SLI PREMIUM Fan connectors · · Only the CPU_FAN and CHA_FAN 1-3 connectors support the ASUS QFAN 2 feature. If you install two VGA cards, we recommend that you plug the rear chassis fan cable to the motherboard connector labeled CHA_FAN1 or CHA_FAN2 for better themal environment. ASUS P5N32-SLI Premium GND +12V Rotation 2-29 7. Chassis intrusion connector (4-1 pin CHASSIS) This connector is for a chassis-mounted intrusion detection sensor or switch. Connect one end of the chassis intrusion sensor or switch cable to this connector. The chassis intrusion sensor or switch sends a high-level signal to this connector when a chassis component is removed or replaced. By default , the pin labeled "Chassis Signal" and " Ground" are shorted with a jumper cap. Remove the jumper caps only when you intend to use the chassis intrusion detection feature. P5N32-SLI PREMIUM ® CHASSIS P5N32-SLI PREMIUM Chassis intrusion connector (Default) 8. ATX power connectors (24-pin EATXPWR, 2 x 4-pin ATX12V) These connectors are for ATX power supply plugs. The power supply plugs are designed to fit these connectors in only one orientation. Find the proper orientation and push down firmly until the connectors completely fit. ATX12V P5N32-SLI PREMIUM Chassis Signal GND +5VSB_MB +12V DC +12V DC +12V DC +12V DC EATXPWR +3 Volts +12 Volts +12 Volts +5V Standby Power OK Ground +5 Volts Ground +5 Volts Ground +3 Volts +3 Volts Ground +5 Volts +5 Volts +5 Volts -5 Volts Ground Ground Ground PSON# Ground -12 Volts +3 Volts ® P5N32-SLI PREMIUM ATX power connectors · · Make sure to remove the cap on the ATX12V connector before connecting an 8-pin EPS +12V power plug. Use only either a 4-pin ATX12V or an 8-pin EPS +12V power plug for the ATX12V connector. Chapter 2: Hardware information 2-30 GND GND GND GND · · · · For a fully configured system, we recommend that you use a power supply unit (PSU) that complies with ATX 12 V Specification 2. 0 (or later version) and provides a minimum power of 550 W. Do not forget to connect the 4-pin/8pin EATX12V power plug; otherwise, the system will not boot. Use of a PSU with a higher power output is recommended when configuring a system with more power-consuming devices. The system may become unstable or may not boot up if the power is inadequate. If you want to use two high-end PCI Express x16 cards, use a PSU with 500 W to 600 W power or above to ensure the system stability. Power supply requirements Heavy Loading CPU DDR533 PCI-E VGA SATA-HD ESATA-HD IDE-HD CD-ROM USB PCI-E 1X PCI SMF 3. 2XE 256MB*4 Nvidia 7950GTX*2 6 2 1 1 2 0 0 +12V-V2 (4 PIN) Io_max (A) Io_rms (A) Vout (V) Po_max (W) 17 12. 35 11. 93 202. 81 +12V-V1 (24PIN) 11. 4 7. 68 11. 9 135. 66 +5V 5. 66 4. 42 5. 022 28. 42 +3. 3V 9. 18 8. 52 3. 316 30. 44 VGA +12V 15. 76 10. 74 11. 42 179. 98 HDD +12V 7. 6 3. 32 11. 95 90. 82 HDD +5V 7. 96 5. 26 4. 993 +5VSB 0. 548 0. 413 5. 054 Total PSU Po_max (W) 678. 18 (continued on the next page) ASUS P5N32-SLI Premium 2-31 Power supply requirements Normal Loading CPU DDR800 VGA SATA-HD ESATA-HD IDE-HD CD-ROM USB PCI PSC 3. 73G 1066 1GB*2 Nvidia 7800GTX*2 SATA*4 1 1 1 2 1 +12V-V2 (4 PIN) Io_max (A) Io_rms (A) Vout (V) Po_max (W) 12. 72 9. 16 11. 94 151. 88 +12V-V1 (24PIN) 11. 44 8. 1 11. 9 136. 14 +5V 6. 88 5. 6 5. 026 34. 58 +3. 3V 8. 72 8 3. 32 28. 95 VGA +12V 8. 88 5. 86 11. 57 102. 74 HDD +12V 4. 04 2. 14 11. 99 48. 44 HDD +5V 4. 14 2. 92 5. 04 20. 87 +5VSB 0. 588 0. 435 5. 05 Total PSU Po_max (W) 2. 97 526. 56 Light Loading CPU DDR667 VGA SATA-HD IDE-HD CD-ROM USB PCI PSC 3. 8G EM64T 512MB*2 Nvidia 7800GTX*1 SATA*2 1 1 1 1 +12V-V2 (4 PIN) Io_max (A) Io_rms (A) Vout (V) Po_max (W) 12. 36 8. 98 11. 93 147. 45 +12V-V1 (24PIN) 7. 6 4. 8 11. 93 90. 67 +5V 8. 44 6. 76 5. 026 42. 42 +3. 3V 3. 24 3. 01 3. 33 10. 79 VGA +12V 4. 28 2. 84 11. 91 50. 97 HDD +12V 4. 34 23. 4 12. 03 52. 21 HDD +5V 3. 58 2. 48 5. 09 18. 22 +5VSB 0. 556 0. 396 5. 066 2. 82 Total PSU Po_max (W) 415. 56 2-32 Chapter 2: Hardware information 9. S/PDIF output connector (4-1 pin SPDIF_02) This connector is for an additional Sony/Philips Digital Interface (S/PDIF) port(s). [. . . ] You can also set the alarm time under operating system using ASUS Music Alarm Utility. ASUS Music Alarm only supports audio CDs. - Chapter : BIOS setup 4. 7. 2 ASUS O. C. Profile Select Menu Item Specific Help Press [Enter] to select. This item allows you to store or load multiple BIOS settings. Load BIOS Profile Save BIOS Profile Load BIOS Profile Phoenix-Award BIOS CMOS Setup Utility Tools Load BIOS Profile Load from Profile 1 Load from Profile 2 Load from File Select Menu Item Specific Help Load BIOS Profile from Profile 1. Load from Profile 1/2 Allows you to load the previous BIOS settings saved in the BIOS Flash. Press <Enter> to load the file. Load from File Allows you to load the previous BIOS file saved in the hard disk/floppy disk/USB flash disk with the FAT32/16/12 format. [. . . ]