User manual ARGUS DC-1620

[. . . ] 9 Deleting Photos . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Flash . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Photo Storage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Downloading Photos . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Click "Finish" to finish ArcSoft software installation. -5- 10. This will automatically install the driver of "Argus Digital Camera". 11. Select installation destination and click the button for "next". -6- 13. Click "Finish" to finish ArcSoft software installation. 15. You have successfully installed "ArcSoft" software and "Argus Digital Camera" driver. You are now ready to start taking and editing photos. Taking Photos 1. Press shutter button for about 4 seconds to open the camera and "Hi -7- 000" will show on LCD at the back of camera. The camera will give out one "beep" sound indicating the camera having entered working state. Hi means no compression (VGA) (about 32 photos, as the case may be) Lo means compression (QVGA) (about 117 photos, as the case may be) 3. Hold the camera steadily, and press the shutter button to take photos. You will hear one beep , indicating your photo has been taken, you may continue taking photos. When the camera is fully loaded with photos, if you press the shutter button again, the buzzer will give out continuous beeps for alarming. When taking photos, the higher" beep " indicates the success of shooting while the lower one indicates the failure of shooting. When taking photos in poor light, the camera will give out two continuous "beeps" , prompting the failure of shooting. Camera Function Control Power off the camera The camera will enter stand-by status automatically about 60 seconds later in case of no operation. Upon starting of camera, press Hi / Lo function button for 3 seconds, the continuous shoot icon " " will appear on the LCD display. The camera will take photos according to required mode specified at that time until you want -8- to stop shooting. The camera will regain previous status after shooting and releasing of shutter button. Note: Under the continuous shooting mode, the shooting may fail due to poor lighting. Upon starting of camera, press delete function button for two times and select the " " icon shown on the LCD display. Pressing the shutter button again within 5 seconds will delete all the photos stored in the memory. Upon starting of camera, press delete function button for one time and select the " " icon shown on the LCD display. Press the shutter button within 5 seconds once to delete the last photo taken. This function will be eliminated later. [. . . ] (2) Please press right key / Hardware Change Scanning, and then the system will execute automatic search. 2. Q: The camera can't work after connection, there's a yellow mark "!" shown at Device Manager / Imaging Devices / Argus Digital Camera. Please follow the steps below: (1) Select Argus Digital Camera in [Device Manager] and press right key / Uninstall (2) Remove USB cable (3) Restart computer (4) Reinsert USB cable 3. Q: After finishing installing software and connecting the camera to the computer, there's "unknown USB device" in Device Manager. A: Please check your camera has been connected well with your computer. [. . . ]