User manual AMX NXA-WAP200G 802.11G WIRELESS ACCESS POINT

[. . . ] instruction manual NXA-WAP200G Modero Wireless Access Point and External Antennas Tou c h Pa n els an d A cc e ss o r ie s AMX Limited Warranty and Disclaimer AMX Corporation warrants its products to be free of defects in material and workmanship under normal use for three (3) years from the date of purchase from AMX Corporation, with the following exceptions: · · · Electroluminescent and LCD Control Panels are warranted for three (3) years, except for the display and touch overlay components that are warranted for a period of one (1) year. Disk drive mechanisms, pan/tilt heads, power supplies, and MX Series products are warranted for a period of one (1) year. AMX Lighting products are guaranteed to switch on and off any load that is properly connected to our lighting products, as long as the AMX Lighting products are under warranty. AMX Corporation does guarantee the control of dimmable loads that are properly connected to our lighting products. [. . . ] Select Internet Protocol (TCP/IP) from the Local Area Connection Properties screen. Click Properties to open the Internet Protocol (TCP/IP) Properties screen. Altering the IP communication protocols of the computer specifies the IP Address pool being used by the computer. This action then assists the communication to the WAP200G located on the same Subnet. 12. Return your source computer to its' previous setting by either clicking the Obtain IP Address Automatically button or entering in your previous Static IP/DHCP Address. Click OK/Close to accept these changes and alter the IP Connection properties of the computer. 40 NXA-WAP200G Wireless Access Point Wireless Device Communication Setup Once the WAP200G is setup with the Static IP Address and the source computer has been restored with Internet communication; the web browser can then be used to access the Static IP Address of the WAP200G (using the correct username and password) and configure the Configuration Utility parameters such as IP Address, and Security options Logging into the WAP200G within Bridge Mode The default Mode setting for the WAP200G is Access Point (AP). Follow the procedures outlined in the Configuring the Communication section on page 21 to establish the communication parameters between the computer and the target WAP200G. Use the information from the Logging into the WAP200G within Access Point Mode section on page 27 to communicate to the WAP200G through a web browser configured for TCP/IP Networking. Press the Administration tab from the bottom row of the Configuration Utility to open the Administration page. From the Commands section of the page, press the on-screen Bridge button to place the WAP200G into the Bridge Mode. When placed in this mode the WAP200G allows devices with only wired 10/100 Ethernet ports such as; printers, PlayStation2s, X-Boxes, PVRs, etc. Click OK (from the confirmation dialog) to reconfirm you want to reboot the WAP200G. A new Temporarily Saved page appears and instructs you to wait a few seconds for the unit to make the necessary changes. Manually cycle power to the WAP200G by disconnecting and re-connecting the power connector from the rear power port on the WAP200G. Verify the computer and the WAP200G are on the same LAN, within the same IP Address pool. If you are having trouble communicating with your WAP200G, refer to the Troubleshooting section on page 71. Type http://192. 168. 1. 240/ (default WAP200G IP Address) into the web browser's Address field (or the URL field) at the top of the browser window. This is the same location where you type in the resolvable web address such as http://www. amx. com. 192. 168. 1. 240 is the default IP Address of the NXA-WAP200G Wireless Access Point. 35) will appear and you will need to enter the following default information: User Name: Admin (Case Sensitive) Password: 1988 14. Click OK to enter the information and access the browser-based configuration screens. NXA-WAP200G Wireless Access Point 41 Wireless Device Communication Setup FIG. 35 WAP200G sample Login page After logging into the WAP200G you can change the default User Name and Password. After connection is re-established, the title 802. 11g Bridge appears below the browser's Address field. The Bridge Mode configuration screens are very similar to the Access Point configuration screens, except for two sections of the Wireless configuration screen and one section within the Advanced configuration screen. Configuring the WAP200G for Secured Bridge Mode Communication After logging into the WAP200G within Bridge Mode, the default Status page appears within the web browser. [. . . ] This is the standard protocol for data transmission over the Internet. The TKIP (Temporal Key Integrity Protocol), pronounced "teekip", is part of the IEEE 802. 11i encryption standard for wireless LANs. TKIP is the next generation of WEP used to secure 802. 11 wireless LANs. TKIP provides per-packet key mixing, a message integrity check and a re-keying mechanism, thus fixing the flaws of WEP. A wide area network (WAN) is a geographically dispersed telecommunications network. [. . . ]