User manual AMX MAX-CSD10 DECODER

[. . . ] instruction manual MAX-CSE MAX Video Encoder AMX Limited Warranty and Disclaimer AMX Corporation warrants its products to be free of defects in material and workmanship under normal use for three (3) years from the date of purchase from AMX Corporation, with the following exceptions: · · · Electroluminescent and LCD Control Panels are warranted for three (3) years, except for the display and touch overlay components that are warranted for a period of one (1) year. Disk drive mechanisms, pan/tilt heads, power supplies, and MX Series products are warranted for a period of one (1) year. AMX Lighting products are guaranteed to switch on and off any load that is properly connected to our lighting products, as long as the AMX Lighting products are under warranty. AMX Corporation does guarantee the control of dimmable loads that are properly connected to our lighting products. [. . . ] Located on the left side of the populated browser window is the Navigation frame which allows a user to navigate throughout the application. Located on the right side of the browser window is the Active frame which displays the pages corresponding to the currently selected option from within the Navigation frame. Access the IP Settings page by clicking the IP Settings link from within the Navigation frame. This page is used to assign the method of communication used by the target MAX unit. Note that both the default IP Configuration setting is DHCP and the corresponding read-only fields display the MAX unit's communication parameters obtained from the DHCP Server during the initial setup. Click on the Static radio box to begin entering the previously obtained Static IP Address information (typically provided by your Network Administrator). Enter the corresponding Static IP Address, Subnet Mask, Gateway, and DNS parameters into their corresponding fields on this page (FIG. Click the Apply button to refresh the screen and save your new communication parameters. Once the browser's progress bar indicates it has completed the temporary acceptance of the new parameters, click the Reboot button to restart the unit and incorporate these changes. Once the unit powers-up, the new Static IP Address is then displayed on the LCD after the appearance of AMX logo (which can take several minutes). MAX Video Encoder 41 Configuring Communication Browser's Address field Navigation frame Active Page frame Stream Status frame First page displayed after login FIG. Confirm the new communication parameters by launching your browser and entering the MAX's new Static IP Address into the browser's Address field. Press the Enter key on your keyboard to regain communication with the target MAX device and launch the initial on-screen Enter Network Password security dialog. Re-enter the words administrator and password into the corresponding User Name/Password fields. Click OK to enter the information and proceed to the Administration page which provides both a descriptive overview of the program stream and lists the currently used firmware. 42 MAX Video Encoder Configuring Communication 11. The next step in the communication process is to prepare a NetLinx Master for communication to the target MAX unit. Refer to the following sections for detailed Master communication setup instructions. Communicating with the target Master via an IP Whether the Master's IP Address was Static or Dynamically obtained (DHCP), use the IP Address information from the Network Addresses dialog to establish communication via the Ethernetconnected Master. Launch NetLinx Studio 2. 4 (default location is Start > Programs > AMX Control Disc > NetLinx Studio > NetLinx Studio 2. 4). Obtain the IP Address of the Master from your System Administrator or if you still do not have an IP Address: 3. Select Settings > Master Communication Settings from the Main menu to open the Master Communication Settings dialog (FIG. Click the Communications Settings button to open the Communications Settings dialog. Click on the NetLinx Master radio button (from the Platform Selection section) to indicate you are working with a NetLinx Master (such as the NXC-ME260/64 or NI-Series of Integrated Controllers). Click on the TCP/IP radio button (from the Transport Connection Option section) to indicate you are connecting to the Master via an IP Address. [. . . ] Example: For detailed usage examples, refer to the 'XCHM' command. 82 MAX Video Encoder NetLinx Programming IR/Serial Send_Commands (Cont. ) Command XCHM Changes the IR output pattern for the 'XCH' send command. Description Syntax: SEND_COMMAND <DEV>, "'XCHM <extended channel mode>'" Variable: extended channel mode = 0 - 4. Example: SEND_COMMAND IR_1, "'XCHM 3'" Sets the IR_1 device's extended channel command to mode 3. Mode 0 Example (default): [x][x]<x><enter> SEND_COMMAND IR_1, "'XCH 3'" Transmits the IR code as 3-enter. SEND_COMMAND IR_1, "'XCH 34'" Transmits the IR code as 3-4-enter. SEND_COMMAND IR_1, "'XCH 343'" Transmits the IR code as 3-4-3-enter. Mode 1 Example: <x> <x> <x> <enter> SEND_COMMAND IR_1, "'XCH 3'" Transmits the IR code as 0-0-3-enter. SEND_COMMAND IR_1, "'XCH 34'" Transmits the IR code as 0-3-4-enter. SEND_COMMAND IR_1, "'XCH 343'" Transmits the IR code as 3-4-3-enter. Mode 2 Example: <x> <x> <x> SEND_COMMAND IR_1, "'XCH 3'" Transmits the IR code as 0-0-3. SEND_COMMAND IR_1, "'XCH 34'" Transmits the IR code as 0-3-4. SEND_COMMAND IR_1, "'XCH 343'" Transmits the IR code as 3-4-3. Mode 3 Example: [[100][100]. . . ] <x> <x> SEND_COMMAND IR_1, "'XCH 3'" Transmits the IR code as 0-3. SEND_COMMAND IR_1, "'XCH 34'" Transmits the IR code as 3-4. SEND_COMMAND IR_1, "'XCH 343'" Transmits the IR code as 100-100-100-4-3. Mode 4: Mode 4 sends the same sequences as the 'CH' command. [. . . ]