User manual AMERICAN AUDIO XDM-352

[. . . ] Damages caused by manual modifications to the device or unauthorized operation by unqualified persons are not subject to warranty. For maintenance and/or service, contact an authorized American DJ® dealer. © American DJ® AUDIO Los Angeles, CA 90058 USA Specifications subject to change without notice. XDM-352 User Instructions page 1 Operating Determinations When installing this mixer, please make sure that the device is not exposed to extreme heat, moisture or dust!Do not operate the mixer in extremely hot (more than 30°C / 100°F) or extremely cold (less than 5°C / 40°F) surroundings. [. . . ] If you wish to connect a third turntable, switch the LINE 3 / PHONO 3 SELECTOR (37) on the rear panel to PHONO 3. You can only control the turntable signal after switching the PHONO 3-LINE 3 / LINE 4 / SWITCH (3) to PHONO 3. · Connect your tape player, tuner, sound effects, CD player, cassette deck or any other line signals to the LINE jacks (27, 28, 29, & 30) on the rear panel. You can only control the line signals after switching the PHONO/LINE switches (3) to LINE. The signal is then controlled via the CH-1, CH-2, CH-3 and CH-4 faders (4). © American DJ® AUDIO Los Angeles, CA 90058 USA Specifications subject to change without notice. XDM-352 User Instructions page 2 Functions 20 4 3 2 14 15 16 17 24 1 21 18 22 23 19 5 6 7 8 9 10 11 12 13 (1) POWER SWITCH (2) BASS/TREBLE CONTROL - Used to increase or decrease the LOWs and HIs of the input signal. (3) LINE/PHONO SWITCH - Used to select the input to be sent to the individual channel. (4) CHANNEL FADER - Used to adjust the output level of the individual channel. (7) CHANNEL ASSIGN SWITCH - Used to select which channel is to be mixed with another. With the CHANNEL ASSIGN switches (7), you can choose which channel is to be mixed with another. EXAMPLE: Set the left CHANNEL ASSIGN switch to channel 1 and the right switch to channel 2 in order to mix the signal of channel I with channel 2. When the crossfader is set to the center position, both channels can be heard at once. (9) BEAT INDICATOR - The LED lights up at every bass beat of the respective source. As soon as the LEDs blink synchronously, the speed of the two sources is synchronized. (10) BOOTH LEVEL CONTROL - THE XDM-352 features a DJ BOOTH monitor system. Connect your monitor system to the BOOTH OUT jacks (33) on the rear panel. You can monitor every channel individually and all possible combinations. Turn the CUE MIXING control to CUE and select CH-1, CH-2, CH-3 or CH-4 with the CUE switches (5). When you turn the CUE MIXING control to PGM (CUE switches without function), you can cue the output signal of the mixer. If the CUE MIXING control is set to the center position, you can cue both the channel signal you selected and the output signal. With the CUE LEVEL control (12), you can adjust the phones volume without changing the output signal. 16 Ohms is recommended. © American DJ® AUDIO Los Angeles, CA 90058 USA Specifications subject to change without notice. [. . . ] (27), (28), (29), (30) LINE I PHONO INPUT JACKS - Input jack for CH-1, CH-2, CH-3 and CH-4. Line level musical instruments with stereo outputs such as Rhythm Machines or Samplers should also be connected to LINE inputs. Channel 3 can be switched to 2 line inputs or 1 line / 1 phono input by using the LINE 3 / PHONO 3 selector (37). Make sure that the STEREO/MONO switch (16) is set to MONO. © American DJ® AUDIO Los Angeles, CA 90058 USA Specifications subject to change without notice. [. . . ]