User manual AMERICAN AUDIO XDM-241

[. . . ] User Instructions XDM-241 "SHREDDER" PREAMP MIXER Thank you for purchasing this American DJ® product. Please read the following instructions before installing or using your new unit. The XDM-241 has a 2 year limited warranty! Safety Instructions Always plug in the power last. [. . . ] Do not operate the mixer in extremely hot (more than 30°C / 100°F) or extremely cold (less than 5°C / 40°F) surroundings. Do not permit operation by persons not qualified for operating the mixer. Please consider that unauthorized modifications on the device are forbidden due to safety reasons! Connections (Refer to diagrams on pages 3 & 4) · Make sure that the power switch (1) is set to OFF. Before connecting other devices to the mixer, all units have to be switched off and the Master Control (11) set to min. · Make sure that the available voltage is the correct voltage (10 Volts) before connecting to power. · In order to obtain the highest sound quality, use high quality American DJ® Ameri-CableTM cables for connecting devices. · For recording, connect your tape recorder or cassette deck to the OUTPUT REC jacks (15). (See diagram) · Connect your turntable(s) to the PHONO 1 jacks (13) or the PHONO 2 jacks (14) on the rear panel. You can only control the record player signal after switching the PHONO/LINE switches (2) to phono. · Connect your tape recorder, tuner, sound effects, CD player, cassette deck or any other line signals to the PHONO/LINE jacks (13 & 14) on the rear panel. You can only control the line signals after switching the PHONO/LINE switches (2) to LINE. The signal is then controlled via the CH-1 and CH-2 faders (3). © American DJ® AUDIO Los Angeles, CA 90058 USA Specifications subject to change without notice. XDM-241 User Instructions page 2 Functions 1 8 ® 5 SHREDDER SCRATCH MIXER 10 MASTER LEVEL +5 +5 11 10 POWER 0 0 0 MASTER -5 -5 7 PHONES -10 -10 5 9 2 MIC 5 -15 L dB R -15 5 0 10 0 10 DJ MIC PHONO 1 LINE 1 PHONO 2 LINE 3 CUE LEVEL LINE 2 LINE 4 2 6 3 CUE channel 2 ch1 ch2 channel 1 3 XDM-241 PREAMP MIXER ch1 FEATHER FADER CROSS FADER PROformer Series ch2 4 (1) POWER SWITCH (2) LINE/PHONO SWITCH - Used to select the input (LINE or PHONO) to be sent to channel 1 or 2. (3) CHANNEL FADER CHANNEL 1 / CHANNEL 2 - Used to adjust the input level of each channel. When the crossfader is set in the center position, both channels can be heard at once. (6) CUE SWITCH DIAL CHANNEL 1 / CHANNEL 2 - Use the cue switch dial in order to select the channel to be monitored. [. . . ] XDM-241 User Instructions page 4 Replacing the Crossfader Instructions for replacing the crossfader: · Disconnect from main power supply · Remove the fader knob. · Only replace cross fader with American DJ® high quality Feather FaderTM (FF-1). Technical Specifications - model XDM-241 Inputs: Microphone Phono Line Output Frequency range Distortion S/N-ratio Tone control Headphone impedance Power supply Dimensions Weight 1. 5mV, 600 Ohm 3mV, 47kOhm 150mV, 27kOhm 7V, peak to peak 20Hz-20KHz, ± 2dB <0. 08% >70dB Treble: 10Khz ± 12dB Bass: 100 Hz ± 12dB 16 Ohms DC 12V 500mA 6. 5" W x 8. 75" D x 3. 75" H 211 x 114 x 285 mm 3. 5 lbs. / 1. 5 kg © American DJ® AUDIO Los Angeles, CA 90058 USA Specifications subject to change without notice. [. . . ]