User manual ALPINE RUX-C701

[. . . ] · MANUAL DE OPERACIÓN Léalo antes de utilizar este equipo. · ISTRUZIONI PER L'USO Si prega di leggere prima di utilizzare il attrezzatura. · ANVÄNDARHANDLEDNING Innan du använder utrustningen bör du läsa igenom denna användarhandledning. ® EN DE FR ES IT ALPINE ELECTRONICS MARKETING, INC. 1-1-8 Nishi Gotanda, Shinagawa-ku, Tokyo 141-0031, Japan Phone 03-5496-8231 ALPINE ELECTRONICS OF AMERICA, INC. [. . . ] Failure to heed them can result in serious injury or death. DO NOT ALLOW CABLES TO BECOME ENTANGLED IN SURROUNDING OBJECTS. Arrange wiring and cables in compliance with the manual to prevent obstructions when driving. Cables or wiring that obstruct or hang up on places such as the steering wheel, shift lever, brake pedals, etc. can be extremely hazardous. DO NOT OPERATE ANY FUNCTION THAT TAKES YOUR ATTENTION AWAY FROM SAFELY DRIVING YOUR VEHICLE. Any function that requires your prolonged attention should only be performed after coming to a complete stop. Always stop the vehicle in a safe location before performing these functions. Failure to do so may result in an accident. DO NOT SPLICE INTO ELECTRICAL CABLES. Never cut away cable insulation to supply power to other equipment. Doing so will exceed the current carrying capacity of the wire and result in fire or electric shock. DO NOT DAMAGE PIPE OR WIRING WHEN DRILLING HOLES. When drilling holes in the chassis for installation, take precautions so as not to contact, damage or obstruct pipes, fuel lines, tanks or electrical wiring. Failure to take such precautions may result in fire. KEEP THE VOLUME AT A LEVEL WHERE YOU CAN STILL HEAR OUTSIDE NOISE WHILE DRIVING. Failure to do so may result in an accident. MINIMIZE DISPLAY VIEWING WHILE DRIVING. Viewing the display may distract the driver from looking ahead of the vehicle and cause an accident. DO NOT USE BOLTS OR NUTS IN THE BRAKE OR STEERING SYSTEMS TO MAKE GROUND CONNECTIONS. Bolts or nuts used for the brake or steering systems (or any other safety-related system), or tanks should NEVER be used for installations or ground connections. Using such parts could disable control of the vehicle and cause fire etc. DO NOT DISASSEMBLE OR ALTER. Doing so may result in an accident, fire or electric shock. USE THIS PRODUCT FOR MOBILE 12V APPLICATIONS. Use for other than its designed application may result in fire, electric shock or other injury. DO NOT INSTALL THE MONITOR NEAR THE PASSENGER SEAT AIR BAG. If the unit is not installed correctly the air bag may not function correctly and when triggered the air bag may cause the monitor to spring upwards causing an accident and injuries. KEEP SMALL OBJECTS SUCH AS BATTERIES OUT OF THE REACH OF CHILDREN. Swallowing them may result in serious injury. If swallowed, consult a physician immediately. USE ONLY IN CARS WITH A 12 VOLT NEGATIVE GROUND. (Check with your dealer if you are not sure. ) Failure to do so may result in fire, etc. DO NOT INSTALL IN LOCATIONS WHICH MIGHT HINDER VEHICLE OPERATION, SUCH AS THE STEERING WHEEL OR SHIFT LEVER. Doing so may obstruct forward vision or hamper movement etc. and results in serious accident. MAKE THE CORRECT CONNECTIONS. Failure to make the proper connections may result in fire or product damage. BEFORE WIRING, DISCONNECT THE CABLE FROM THE NEGATIVE BATTERY TERMINAL. Failure to do so may result in electric shock or injury due to electrical shorts. 2-EN CAUTION This symbol means important instructions. Failure to heed them can result in injury or material property damage. PRECAUTIONS Temperature Be sure the temperature inside the vehicle is between +60°C (+140°F) and ­10°C (+14°F) before turning your unit on. HALT USE IMMEDIATELY IF A PROBLEM APPEARS. Failure to do so may cause personal injury or damage to the product. Return it to your authorized Alpine dealer or the nearest Alpine Service Centre for repairing. Installation Location Make sure the RUX-C701 will not be installed in a location subjected to: · Direct sun and heat · High humidity and water · Excessive dust · Excessive vibrations HAVE THE WIRING AND INSTALLATION DONE BY EXPERTS. The wiring and installation of this unit requires special technical skill and experience. To ensure safety, always contact the dealer where you purchased this product to have the work done. FR Maintenance If you have problems, do not attempt to repair the unit yourself. Return it to your Alpine dealer or the nearest Alpine Service Station for servicing. USE SPECIFIED ACCESSORY PARTS AND INSTALL THEM SECURELY. Be sure to use only the specified accessory parts. Use of other than designated parts may damage this unit internally or may not securely install the unit in place. This may cause parts to become loose resulting in hazards or product failure. ES Operation About the control unit operation For details about the control unit operation, refer to the PXA-H701 Owner's manual. ARRANGE THE WIRING SO IT IS NOT CRIMPED OR PINCHED BY A SHARP METAL EDGE. Route the cables and wiring away from moving parts (like the seat rails) or sharp or pointed edges. If wiring passes through a hole in metal, use a rubber grommet to prevent the wire's insulation from being cut by the metal edge of the hole. DE DO NOT INSTALL IN LOCATIONS WITH HIGH MOISTURE OR DUST. Avoid installing the unit in locations with high incidence of moisture or dust. Moisture or dust that penetrates into this unit may result in product failure. IT SE 3-EN Installation and Connections IMPORTANT Please record the serial number of your unit in the space provided below and keep it as a permanent record. The serial number plate is located on the rear of the control unit. Accessories Display cable Microphone Velcro fastener for mounting control unit SERIAL NUMBER: INSTALLATION DATE: INSTALLATION TECHNICIAN: PLACE OF PURCHASE: Pan head screw (M3 x 5) Flat head screw (M5 x 8) Flush mount To prevent external noise from entering the audio system. · Locate the unit and route the leads at least 10 cm away from the car harness. · Keep the battery power leads as far away from other leads as possible. [. . . ] WARNING When making cut-outs, be careful not to damage pipes, tanks, electric wires, etc. Doing so could lead to accidents or fire. Face plate Self-tapping screw (M2. 6 x 8) x 4 Basic Connections Diagram 2 After step 2 on "Mounting other units" of "Mounting the control unit" page 5, remove the side bracket. Side bracket CAUTION Do not connect or disconnect the display cable when the power of the unit is on. Display Side bracket 3 Remove the spacer from the bracket. Spacer Bracket Display cable PXA-H701 CENTER (L) SELECTABLE SUBWOOFER MIC (R) FRONT 1 FRONT 2 REAR SUBWOOFER CONTROL UNIT OUTPUT INPUT GUIDE (L) (R) ANALOG 1 Ai­NET IN ANALOG 2 CHANGER IN ANALOG 3 POWER SUPPLY CD/DVD H. U. CHG DIGITAL 1 DIGITAL 2 DVD DIGITAL 3 (FULL RANGE /TWEETER) 6-EN Others Specifications Weight: Illumination colour: Control unit Green 159 g (5 oz) Dimensions Control unit Width Height Depth 170 mm (6-3/4") 46 mm (1-13/16") 24 mm (15/16") Due to continuous product improvement, specifications and design are subject to change without notice. The illustrations included in these instructions may appear different from the actual product due to printing conditions. [. . . ]