User manual AEG OF 500 S

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual AEG OF 500 S. We hope that this AEG OF 500 S user guide will be useful to you.


AEG OF 500 S : Download the complete user guide (4699 Ko)

Manual abstract: user guide AEG OF 500 S

Detailed instructions for use are in the User's Guide.

[. . . ] 30 000 min-1 Maximum no­load speed in case of ineffective no­load speed limitation . Advice for your safety J Please pay attention to the safety instructions in the attached leaflet!It is recommended to wear gloves, sturdy non slipping shoes and apron. J Sawdust and splinters must not be removed while the machine is running. [. . . ] Use The router can be used for rabbeting, rounding off, chamfering, routing of edges, as well as pitting in wood and plastic. The router can additionally be used as a straight grinder and in combination with a flexible shaft (accessory). Locking screw to fix the motor: After loosening the screw the motor can be removed from the cage and be used as a straight grinder. Parallel guide for parallel cutting with a distance of up to 240 mm from edge. In the interest of continuous improvement of our products, technical specifications are subject to alteration without prior notice. Always disconnect the plug from the socket before carrying out any work on the machine. exchanging router cutters The collet diameter must be corresponding to the shaft diamter. Nsert the shaft of the tool as far as possible into the collet and tighten with clamping nut. To take out router cutter, loosen adjusting nut until the cutter can be removed. The following collets can be used: ø 6 mm, ø 8 mm, ø 1/4"* (The ø relates to the shaft diameter of the router). Push a new collet into adjusting nut until it Screw adjusting nut with collet onto After setting the required distance from the edge tighten the wing screws. For close cutting of boards coated on one or both sides, the plastic corner guides are screwed on, as figure. Insert the precision adjustment screw (B) fromthe right or left into the base plate. Check the settings with a test cut and make possible corrections with aid of fine adjustment. Industrial vacuum cleaners as well as household vacuum cleaners are suitable. Device turning it slightly and connect the other end of the hose with a vacuum cleaner. Lower cage until the router cutter Lower the depth gauge onto the required Pick value off the scale, add required Three cutting depths can be set with the screws on the revolving depth gauge: Set the first two cutting depths on the longer screws. tighten screws again and Secure with the locking nuts against distorting. Under the effect of extreme electromagnetic interferences from the outside, tempo­rary variations in the speed of rotation could arise in particular cases. Router ø in mm 4­16 18­36 4­20 22­36 Router working material HSS HSS HM HM Soft wood Panels made of wood chips ­ ­ G F Plastic, Perspex D­E C­D E­F D­E To lock, depress the front part of the sliding switch. [. . . ] In order to guarantee constant readiness for operation, the machine should be checked for worn carbon brushes at one of the AEG after­sales service agencies. Should components need to be replaced which have not been described, please contact one of our AEG service agents (see our list of guarantee/service addresses). As well as the machine type printed on the label and order the drawing at your local service agents or directly at: Atlas Copco Electric Tools GmbH, Postfach 320, D­71361 Winnenden. Pour le fraisage d'affleurement de plaques revêtues d'une ou des deux faces, fixer la butée angulaire en matières plastiques conformément à la figure ci­contre. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE AEG OF 500 S




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual AEG OF 500 S will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.