User manual AEG DD 8891 M9

[. . . ] € La distance minimum entre la superficie de support des récipients sur le dispositif de cuisson et la partie la plus basse de la hotte de cuisine ne doit pas être inférieure à 50cm dans le cas de cuisinières électriques et de 65cm dans le cas de cuisinières à gaz ou mixtes. Extérieure): Hauteur (recyclage): Largeur: Profondeur: Puissance nominale totale: Moteur: Eclairage: Longueur du câble: Branchement électrique: 85, 5-129, 5 96-140 59, 8 39 290 W 250 W 2 x 20 W 150 cm 220-240 V DD 9893 85, 5-129, 5 96-140 89, 8 39 290 W 250 W 2 x 20 W 150 cm 220 - 240 V Accessoires/Matériel de montage 1 manchon de réduction 1 déflecteur (avec rallonge) 1 clé à chenillette pour vis torx 1 support de fixation pour le groupe moteur 1 support de fixation cheminées (3 pièces à assembler) 6 vis 5 x 45 mm 6 chevilles Ø 8 mm 2 vis 2, 9 x 6, 5 8 vis 3, 5 x 6, 5 4 vis 4 x 8 2 bouchons grand modèle 2 bouchons petit modèle 57 Branchement électrique Consignes de sécurité pour l’électricien La tension électrique doit correspondre à la tension reportée sur la plaque signalétique située à l’intérieur de la hotte. Assembler le support cheminée (3 parties) Les trois parties doivent être fixées entre elles avec 4 vis, l’extension du support est réglagle et doit correspondre à la largeur interne de la cheminée téléscopique. 81 63 Safety warnings • When used as an extractor unit, the hood must be fitted with a hose having preferably the same diameter as the outlet hole. [. . . ] If the hood is to be used with a charcoal filter, the saturation indicator light must be enabled as follows: Set in "OFF" the hood. At first only the grease filter LED F will light up, but when the charcoal filter LED C lights up the saturation indicator will be enabled. To disable it: Press buttons 3 and 4 again simultaneously and hold them for 3 seconds, until the charcoal filter LED goes out. Grease filter LED (F) LED F will start to flash when it is time to clean the grease filter. Always comply with the maintenance instructions for the grease filter. Charcoal filter LED (C) The charcoal filter LED C will start to flash when the charcoal filter needs to be replaced. Resetting the saturation indicator After cleaning or replacing the filters, press button 3 for 3 seconds until the grease filter LED F or the charcoal filter LED C stops flashing. Before performing any maintenance operation, isolate the hood from the electrical supply by switching off at the connector and removing the connector fuse. Or if the appliance has been connected through a plug and socket, then the plug must be removed from the socket. Air suction panels Remove the perimeter air suction panels to access the grease filters. € DD 9893 The perimeter air suction panels are attached to the cooker hood by a series of pins and coupling springs; pull them outwards and detach them from the fastening cable. 3 When refitting the perimeter air suction panels, ALWAYS reattach the fastening cables. Make sure the panels are attached to the cooker hood properly (snap-fastened). 3 70 • DD 9863 Pull the panel (FRONT SIDE) downward with decision, unscrew safety knob and unhook it from the rear hinge. 3a Clean the perimeter air suction panels as often as the grease filters (for more information about gentle cleaning methods, read the paragraph “Cleaning” in the pages that follow). Inner crosspiece - DD 9893 The inner crosspiece should be removed in order to access the grease filters and the inside of the cooker hood (for example: when performing maintenance work on the carbon filters). Keep the crosspiece supported during removal/fitting procedures, in order to prevent it from falling and damaging other objects. 4 71 Metal grease filter • The purpose of the grease filters is to absorb grease particles which form during cooking and it must always be used, either in the external extraction or internal re-circulation function. Attention: the metal grease filters must be removed and washed, either by hand or in the dishwasher, every four weeks. Removing the metal grease filters • Push it towards the back of the unit and then pull it down and out. 5 Hand washing Soak grease filters for about one hour in hot water with a greaseloosening cleaner, then rinse off thoroughly with hot water. Select most powerful washing programme and highest temperature, at least 65°C. [. . . ] Uk Customer Services Department Major Appliances AEGElectrolux Addington Way Luton Bedfordshire LU4 9QQ 08705 350 350 (*) * calls to this number may be recorded for training purposes 77 Installation Technical Details DD 9863 Dimensions (in cm): Height (Extract. Power: Motor: Lighting: Length of the cable: Electrical connection: Fuse rating: 85, 5-129, 5 96-140 59, 8 39 290 W 250 W 2 x 20 W 150 cm 220-240 V 5At DD 9893 85, 5-129, 5 96-140 89, 8 39 290 W 250 W 2 x 20 W 150 cm 220 - 240 V 5At Mounting accessories included 1 reduction flange 1 deflector (with extensions) 1 Allan wrench for torx screws 1 fixing bracket for motor unit 1 support bracket for flues (3 pieces to assemble) 6 screws 5 x 45 mm 6 dowels Ø 8 mm 2 screws 2. 5 4 screws 4 x 8 2 large plug caps 2 small plug caps 78 Electrical connection Safety warnings for the electrician The mains power supply must correspond to the rating indicated on the plate situated inside the hood. If provided with a plug connect the hood to a socket in compliance with current regulations and positioned in an accessible area. [. . . ]