User manual ACRON SK1L LCD KEYPAD

[. . . ] LCD KEYPAD Installation & Programming Manual SK1L Use with SC800/1600 Series control panels P/N 64812820 A PDF 10/1/97 Downloaded from: http://www. guardianalarms. net GENERAL DESCRIPTION OF SK1L The SK1L is an EEPROM based Digital Arming Station with LCD display that provides full system status from one or more convenient locations. The SK1L can be programmed to meet a wide range of Residential and Commercial applications. [. . . ] The SK1L keypad needs to have its keypad address and its text messages programmed. If you are using partitioned mode in the SC800 / 1600 then you must set the keypad address to match the partition to which it is assigned. Refer to the SC800 / 1600 installation manual for instructions on Partitioned mode. Older SK1L keypads do not have programmable text messages and the keypad address is the only programmable location. 2 CHANGING DATA OR TEXT THROUGH THE KEYPAD 1) Enter the following sequence at the keypad to activate keypad programming mode: [*&0]+[IIII]+[9] [ * & 0 ] = Pressed simultaneously [ I I I I ] = Installer's code (factory default = 7777) programmed into control panel. This is indicated by the top line in the display saying PROGRAM# followed by #0 the actual memory location. The current data in that address is displayed at the left on the second line of the display after you press [ # ]. 3) Using the [ * ] key you can switch the cursor back and forth between the "program#" value and the "data" value. To change the memory location put the cursor on the "program#" value using the [ * ] key and enter a new three digit memory location, i. e. To change the data put the cursor on the data value using the [ * ] key and then enter new data . 4) The programming defaults for the domestic SK1L are shown in Figure 2. [. . . ] The SC800/1600 installation manuals (P/N 64812821) cover panel programming functions, locations, and partitioning mode. Refer to the SC800 /1600 installation manuals and the SK1L owner's manual (P/N 64812819) for information on WARRANTY and LIMITATION OF LIABILITY. v v FIGURE 1 Character map for programming Alpha-Numeric descriptions using the SK1L keypad. 3 FIGURE 2 SK1L LCD KEYPAD EEPROM MEMORY MAP Location 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 MESSAGES "0" - Keypad ID ( Starts from 0 ) "Z" - Letter used to identify zone number "KYPD PGM" - Local Programming prompt "PANEL PGM" - Panel Programming prompt "NOT READY" - Message indicating the system is not secure "ARMED INST" - Message indicating the system is Armed/ Instant "ALARM" - Message indicating the zone has caused an alarm "TROUBLE" - Message indicating a Fire or Day/Night zone is open "ARMED" - Message indicating the system is armed "READY" - Message indicating the system is Ready to Arm "BYPASSED" - indicates the specific zone is not armed "VIOLATED" - indicates Burglary zone is not secure "AC-OFF" - indicates the AC power is not available "LOW BATT. " - indicates either no or low battery "FAIL COMMUNICATE" - indicates communication failure "PANEL LINE DOWN" - indicates no data to keypad Reserved for future use DAY MM-DD HH:MM Time / Date display format header *** - indicates undefined day of week SUN - indicates First day of the week MON - indicates Second day of the week TUE - indicates Third day of the week WED - indicates Fourth day of the week THU - indicates Fifth day of the week FRI - indicates Sixth day of the week SAT - indicates Seventh day of the week "USER" - Message identifying system user "STATION" - Message TO identifywhich keypad address was used (Select 0-7) ALPHA / NUMERIC DATA USER/INSTALLER MENU PROMPTS "SET TIME/DATE" "SET ENTRY TIME" "SET EXIT TIME" "EDIT USER CODE" "EDIT ZONE NAME" "CALL STATION" "ANSWER CALL" "PROGRAMMING" "VIEW HISTORY" "SEND" "RETRIEVE" "COPY PROM" HISTORY ABBREVIATIONS "AL" - ALARM "TB" - TROUBLE "RT" - RESTORE "BP" - BYPASS "AX" - AUXILIARY "E1" - EMERGENCY KEYPAIR 1 "E2" - EMERGENCY KEYPAIR 2 "E3" - EMERGENCY KEYPAIR 3 "E4" - EMERGENCY KEYPAIR 4 "DU" - DURESS "CL" - CLOSE "OP" - OPEN "AR" - ALARM RESET "ST" - STATION "ET" - ENTER TEST MODE "DA" - DOOR ACCESS Reserved for future use 4 [. . . ]