User manual ACER AL1751W

[. . . ] 6 3. 2 Standard Timing Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 3. 3 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Preface This manual is designed to assist users in setting up and using the LCD Monitor. Information in this document has been carefully checked for accuracy; however, no guarantee is given to the correctness of the contents. [. . . ] Attempting this will result in damaging the Monitor and Monitor stand. 2 1. 4 Detaching LCD Monitor from Its Stand 1. Remove the stand from main body Figure 1-4 1. 5 Interface for Arm Applications Before installing to mounting device, please refer to Fig. 1-4. The rear of this LCD display has four integrated 4 mm, 0. 7 pitches threaded nuts, as well as four 5 mm access holes in the plastic covering as illustrated in Figure 1-5. These specifications meet the VESA Flat Panel Monitor Physical Mounting Interface Standard (paragraphs 2. 1 and 2. 1. 3, version 1, dated 13 November 1997). Figure 1-5 Note :Please using Ø 4mm x 8mm (L) screw for this application. 1. 6 System Installation Figure 1-6 1. 6. 1 Connecting the Display 1. Connect one end of the signal cable to the LCD Monitor's VGA port. (See Fig 1-6) 3. Attention: This device must be connected to an off-the-shelf video cable in order to comply with FCC regulations. A ferrite-core interface cable is included in the LCD Monitor package. This device will not be in compliance with FCC regulations when a non-ferrite-core video cable is used. 1. 6. 2 Connecting the AC Power 1. Connect the AC adapter's DC output connector to the DC Power Jack of the monitor. Connect the power cord to an AC power source. 1. 6. 3 Connecting the Audio Cable 1. Connect the audio cable to the " LINE OUT " jack on your PC's audio card or to the front panel's "AUDIO OUT" jack of your CD ROM drive. Connect the other end of the audio cable to the LCD Monitor's " LINE IN " jack. 1. 7 Power Management System This LCD Monitor complies with the VESA DPMS (version 1. 0) Power Management guidelines. The VESA DPMS provides four power saving modes through detecting a horizontal or vertical sync. When the LCD Monitor is in power saving mode, the monitor screen will be blank and the power LED indicator will light orange. 3 Chapter 2 Display Controls 2. 1 User Controls A brief description and the location of all LCD Monitor function controls and indicators: Figure 2-1 Figure 2-2 1 2 3 4 Indicator for Power Power Function Select Adjustment LED lights Green color --- Power is ON. OSD function for adjusting / Volume adjusting. 2. 2 Adjusting the Monitor's Display The monitor has six function control buttons to select among functions shown on OSD menu, designed for easy user-viewing environments. 2. 2. 1 OSD Function Menu To access OSD Main menu, simply press menu button and the menu diagram will pop up on the screen as shown on. Continue pressing the Function Select buttons to scroll through the entire menu items , then press Adjustment Control buttons to adjust content of selected item. Attention Firmware revision may have been updated into a latest version while the version number shown on all OSD menus in this manual will stay as Ver. 1. 00. 4 2. 2. 2 Icon Function Description Function Brightness Contrast H. Position Aspect OSD Transparency Phase Function Description Clock Color Temperature OSD H. [. . . ] If there are, take advantage of the "Clock" function in OSD menu and adjust (by increment or decrement numbers) until those bars disappear. Move to "Phase" function in OSD menu again and adjust the monitor screen to its most clear display. Click "No" on "Shut Down Windows" and back to the normal PC operating environment. PROBLEM There is no picture on LCD Monitor If there's no picture on the LCD Monitor, please perform the following steps: 1. Make sure the power indicator on the LCD Monitor is ON, all connections are secured, and the system is running on the correct timing. [. . . ]