User manual 3COM WA2210-AG_INDOORSINGLEBANDAP

[. . . ] H3C WA2200 Series WLAN Access Points Installation Manual Hangzhou H3C Technologies Co. , Ltd. Manual Version: 6PW104-20091228 Copyright © 2008-2009, Hangzhou H3C Technologies Co. , Ltd. and its licensors H3C Technologies Co. , Ltd. , a subsidiary of 3Com Corporation. All Rights Reserved No part of this manual may be reproduced or transmitted in any form or by any means without prior written consent of Hangzhou H3C Technologies Co. , Ltd. Trademarks H3C, , Aolynk, , H3Care, , TOP G, , IRF, NetPilot, Neocean, NeoVTL, SecPro, SecPoint, SecEngine, SecPath, Comware, Secware, Storware, NQA, VVG, V2G, VnG, PSPT, XGbus, N-Bus, TiGem, InnoVision and HUASAN are trademarks of Hangzhou H3C Technologies Co. , Ltd. All other trademarks that may be mentioned in this manual are the property of their respective owners. Notice The information in this document is subject to change without notice. Every effort has been made in the preparation of this document to ensure accuracy of the contents, but all statements, information, and recommendations in this document do not constitute the warranty of any kind, express or implied. About This Manual Organization The H3C WA2200 Series WLAN Access Points Installation Manual is organized as follows: Chapter 1 Product Overview 2 Installation Preparations 3 Installation of Indoor APs Contents Introduces the hardware configuration, appearances, and interfaces of the WA2200 series. [. . . ] In mountainous areas or lightning areas, the protection angle should be less than 30 degrees. The lightning protection grounding (for example, the grounding of the lightning rod) should be connected to the earthing conductor of the equipment room. The antenna support is already prepared according to the design requirements. A feeder lightning rod is already installed and grounded according to the design requirements. Power lightning arrester, port lightning protector, and feeder lightning arrester are recommended for outdoor installations. The power lightning arrester and the feeder lightning arrester should be near the AP, and the network interface lightning arrester should be near the peer device of the AP. The network interface lightning arrester should be installed where the network cable is just led out of the room. Ensure that the devices at the two ends of the cable are well grounded. 4 5 Lightning arrester 6 Feeder 7 Outdoor lightning arrester 8 Network cable After you have completed the preparations, you can start installing the AP. The installation of indoor models is different from that of the outdoor models. For details, refer to 3 "Installation of Indoor APs" on page 3-1 and 4 "Installation of Outdoor APs" on page 4-1. 2-4 3 Installation of Indoor APs You can directly place an indoor model (including the enhanced model) on a desk. The rubber feet on the bottom of the AP help you to place it horizontally. The following introduces the wall-mounting procedure of the indoor models and enhanced model in detail. Installation Flowchart Figure 3-1 shows the installation flowchart of the indoor models and enhanced model. Figure 3-1 Installation flowchart of an indoor AP Start Determine the installation position Install the AP Connect the power supply and network End Determining the Installation Position Determine the installation position by observing the following principles: Leave as few obstacles (such as wall and ceiling) as possible between the AP and stations. Keep the AP far away from electronic devices (such as microwave oven) that may generate RF noise. Install the AP in a place where it will not hinder people's daily work and life. Do not install the AP in a place where water seeping, water soaking, and condensing occur. Prevent water or moisture from entering the AP. Ensure the intensity and structure of the ceiling meet the requirements for ceiling mounting of the AP. You are recommended to reinforce the ceiling using boards if it is not strong enough. A padlock is required to prevent any falloff in case of shocks. 3-1 Installing the AP The following describes how to install the AP on a wall. Installing the Wall-Mounting Bracket on a Wall Installing the AP on the Wall-Mounting Bracket Locking the AP onto the Wall-Mounting Bracket (Optional) Installing the Wall-Mounting Bracket on a Wall Follow these steps to install the wall-mounting bracket on a wall: Step1 Drill holes 6 mm (0. 24 in) in diameter on the wall where the AP should be mounted. The drilled holes should correspond to those in the wall-mounting bracket. There are eight installation holes in total in the wall-mounting bracket. [. . . ] Step5 Use waterproof tape to wrap the joint between the waterproof cover and the cable. 4-15 Connecting an optical fiber Be sure to follow the instructions below when connecting a fiber cable. When connecting the AP to the remote device through a fiber cable, use an appropriate SFP module. These SFP modules use single-mode optic fibers and have a transmission distance of 15 km (9. 32 miles). You need to configure an SFP module and a waterproof cover when connecting the AP to an uplink device through a fiber cable, as shown in Figure 4-20. Figure 4-20 Connect a fiber cable Follow these steps to connect a fiber cable: Step1 Insert an SFP module into the Ethernet optical interface on the AP. [. . . ]