User manual 3COM SS3 BASELINE10/100 SWTCH 12PT

[. . . ] SuperStack® 3 Baseline 10/100 Switch 12-Port (3C16464C) and 24-Port (3C16465C) User Guide DUA1646-4AAA05 Base line 10/1 00 Sw itch 3C Supe 16465C rSta ® ck 3 INTRODUCTION The SuperStack® 3 Baseline 10/100 Switch is a versatile, easy-to-use unmanaged switch. It is ideal for users who want the high-speed performance of 10/100 switching but do not need sophisticated management capabilities. The Baseline 10/100 Switch has 12 or 24 shielded RJ-45, 10/100 Mbps auto-negotiating ports on the front panel. Each port automatically determines the speed and duplex mode of the connected equipment and provides a suitable switched connection. [. . . ] Impédance à la terre Power Cord Set This must be approved for the country where it will be used. e. g. If installing the Switch unit in a stack with SuperStack 3 Hub units, the Baseline 10/100 Switch unit must be installed below the narrower Hub units. The unit must be connected to an earthed (grounded) outlet to comply with international safety standards. The appliance coupler (the connector to the unit and not the wall plug) must have a configuration for mating with an EN60320/IEC320 appliance inlet. You can only remove power from the unit by disconnecting the power cord from the outlet. This unit operates under SELV (Safety Extra Low Voltage) conditions according to IEC 60. The conditions are only maintained if the equipment to which it is connected also operates under SELV conditions. Only connect an Advanced Redundant Power System (3C16070, 3C16071, 3C16071A or 3C16071B) or Redundant Power System (3C565047) to the Redundant Power System socket. U. S. A. and Canada s s The cord set must be UL-approved and CSA certified. 18 AWG Type SV or SJ 3-conductor The cord set must have a rated current capacity of at least 10A. The attachment plug must be an earth-grounding type with a NEMA 5-15P (15A, 125V) or NEMA 6-15P (15A, 250V) configuration. The supply plug must comply with Section 107-2-D1, Standard DK2-1a or DK2-5a. The supply plug must comply with BS1363 (3-pin 13-amp) and be fitted with a 5A fuse which complies with BS1362. The mains cord must be <HAR> or <BASEC> marked and be of type HO3VVF3GO. 75 (minimum). The supply plug must comply with CEE7/7 ("SCHUKO") The mains cord must be <HAR> or <BASEC> marked and be of type HO3VVF3GO. 75 (minimum). !! s s ! Denmark Switzerland UK s s s ! s ! Europe s s France and Peru only This unit cannot be powered from IT supplies. If your supplies are of IT type, this L'INFORMATION ! DE SÉCURITÉ IMPORTANTE France et Pérou uniquement: Ce groupe ne peut pas être alimenté par un dispositif à impédance à la terre. Si vos alimentations sont du type impédance à la terre, ce groupe doit être alimenté par une tension de 230 V (2 P+T) par le biais d'un transformateur d'isolement à rapport 1:1, avec un point secondaire de connexion portant l'appellation Neutre et avec raccordement direct à la terre (masse). La prise mâle d'alimentation doit respecter la norme SEV/ASE 1011. La prise secteur doit être conforme aux normes CEE 7/7 ("SCHUKO") LE cordon secteur doit porter la mention <HAR> ou <BASEC> et doit être de type HO3VVF3GO. 75 (minimum). ! s s s ! WICHTIGE SICHERHEITSINFORMATIONEN Bitte unbedingt vor dem Einbauen des Baseline 10/100 Switch Einheit die folgenden Sicherheitsanweisungen durchlesen. WARNUNG: Die Installation und der Ausbau des Geräts darf nur durch Fachpersonal erfolgen. !! Die Netzsteckdose muß in der Nähe des Geräts und leicht zugänglich sein. Die Stromversorgung des Geräts kann nur durch Herausziehen des Gerätenetzkabels aus der Netzsteckdose unterbrochen werden. Der Betrieb dieses Geräts erfolgt unter den SELV-Bedingungen (Sicherheitskleinstspannung) gemäß IEC 60. [. . . ] Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. Reorient the receiving antenna. Plug the equipment into a different outlet so that equipment and receiver are on different branch circuits. VCCI Statement If necessary, the user should consult the dealer or an experienced radio/television technician for additional suggestions. The user may find the following booklet prepared by the Federal Communications Commission helpful: How to Identify and Resolve Radio-TV Interference Problems BSMI Statement TECHNICAL SUPPORT The following options are available for technical support: !Check the 3Com knowledgebase at http://knowledgebase. 3com. com Browse the 3Com web site on http://www. 3com. com Telephone Number 1 800 678 515 800 933 486 +61 2 9937 5085 or 000800 6501111 001 800 61 009 03 5783 1270 1800 801 777 0800 446 398 +61 2 9937 5083 1235 61 266 2602 Please have your product model name, part number, hardware revision number and serial number along with all relevant details of the problem to hand before calling your Network Supplier or 3Com on the numbers below. ! Country Asia, Pacific Rim Australia Hong Kong India Indonesia Japan Malaysia New Zealand Pakistan Philippines Europe, Middle East and Africa From anywhere in these regions, call: Country P. R. [. . . ]